Electronic Components Datasheet Search |
|
LM5008MMX Datasheet(PDF) 9 Page - Texas Instruments |
|
|
LM5008MMX Datasheet(HTML) 9 Page - Texas Instruments |
9 / 24 page TOFF = VFB (6.35 x 10 -6 x RCL) 0.285 + 10 -5 STOP RUN RON LM5008 RON/SD VIN Input Voltage LM5008 www.ti.com SNVS280G – APRIL 2004 – REVISED MARCH 2013 Over-Voltage Comparator The feedback voltage at FB is compared to an internal 2.875V reference. If the voltage at FB rises above 2.875V the on-time pulse is immediately terminated. This condition can occur if the input voltage, or the output load, change suddenly. The buck switch will not turn on again until the voltage at FB falls below 2.5V. On-Time Generator and Shutdown The on-time for the LM5008 is determined by the RON resistor, and is inversely proportional to the input voltage (Vin), resulting in a nearly constant frequency as Vin is varied over its range. Equation 4 shows the on-time equation for the LM5008. TON = 1.25 x 10 -10 x R ON / VIN (4) See Figure 4. RON should be selected for a minimum on-time (at maximum VIN) greater than 400 ns, for proper current limit operation. This requirement limits the maximum frequency for each application, depending on VIN and VOUT. See Figure 5. The LM5008 can be remotely disabled by taking the RON/SD pin to ground. See Figure 12. The voltage at the RON/SD pin is between 1.5 and 3.0 volts, depending on Vin and the value of the RON resistor. Figure 12. Shutdown Implementation Current Limit The LM5008 contains an intelligent current limit OFF timer. If the current in the Buck switch exceeds 0.5A the present cycle is immediately terminated, and a non-resetable OFF timer is initiated. The length of off-time is controlled by an external resistor (RCL) and the FB voltage (see Figure 6). When FB = 0V, a maximum off-time is required, and the time is preset to 35µs. This condition occurs when the output is shorted, and during the initial part of start-up. This amount of time ensures safe short circuit operation up to the maximum input voltage of 95V. In cases of overload where the FB voltage is above zero volts (not a short circuit) the current limit off-time will be less than 35µs. Reducing the off-time during less severe overloads reduces the amount of foldback, recovery time, and the start-up time. The off-time is calculated from Equation 5. (5) The current limit sensing circuit is blanked for the first 50-70ns of each on-time so it is not falsely tripped by the current surge which occurs at turn-on. The current surge is required by the re-circulating diode (D1) for its turn- off recovery. N-Channel Buck Switch and Driver The LM5008 integrates an N-Channel Buck switch and associated floating high voltage gate driver. The gate driver circuit works in conjunction with an external bootstrap capacitor and an internal high voltage diode. A 0.01µF ceramic capacitor (C4) connected between the BST pin and SW pin provides the voltage to the driver during the on-time. Copyright © 2004–2013, Texas Instruments Incorporated Submit Documentation Feedback 9 Product Folder Links: LM5008 |
Similar Part No. - LM5008MMX |
|
Similar Description - LM5008MMX |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |