75W Single Output Switching Power Supply

WWW.ASTRODYNETDI.COM

ASTRODYNE USA: 1-800-823-8082

ASTRODYNE PACIFIC: 886-2-26983458

INPUT SPECIFICATIONS

Input Voltage Range

90 ~ 264 VAC; 127~370 Volts(DC)

Frequency Range

47-63 Hz

Inrush Current, typ: (cold start)18Amps@115VAC / 36Amps@230VAC

Input Current, typ.

1.9Amps@115VAC

1.1Amps@230VAC

Leakage current

< 1mAmps /240VAC

Min Load

See Selection Chart

OUTPUT SPECIFICATIONS

Voltage and Current

See Selection Chart

Line Regulation

±1.0%

Load Regulation

±3.0%: 3.3~5Volts(DC)

±2.0%: 12~15Volts(DC)

±1.0%: 24~48Volts(DC)

Voltage Tolerance (Note2)

See Selection Chart

Ripple/Noise (Note 1)

See Selection Chart

Hold Up Time,typ @ FL

60mS/230VAC

12mS/115VAC

Setup, Rise Time @ FL

100ms, 35m/230VAC

100mS, 35mS/115VAC

Over Voltage Protection

3.8 ~ 4.45Volt(DC): 3.3Volts(DC)

5.75 ~ 6.75Volt(DC): 5Volts(DC)

13.8 ~ 16.2Volt(DC): 12Volts(DC)

17.25 ~ 20.25Volt(DC): 15Volts(DC)

27.6~ 32.4Volt(DC): 24Volts(DC)

57.6~ 67.2Volt(DC): 48Volts(DC)

Hiccup mode, auto recover

Over Current Protection

115 ~ 150% rated output power

Hiccup mode, auto recover

DC Volt Adjust

See Selection Chart

Peak Load, 10S(Note 3)

See Selection Chart

GENERAL SPECIFICATIONS

Safety

UL60950-1,

TUV EN60950-1 Approved

Insulation Resistance

≥ 100MΩ / 500Volts(DC)

EMI

Compliance to EN55022B (CISPR22B)

Harmonic Current

Compliance to EN61000-3-2,-3

Efficiency, typ.

69% (LPS-75-3.3)

77% (LPS-75-5)

80% (LPS-75-12)

81% (LPS-75-15)

83% (LPS-75-24)

83%(LPS-75-48)

Isolation

3000VAC Input - Output

1500VAC Input - Ground

500VAC Output - Ground

EMS

Compliance to

EN61000-4-2, 3, 4, 5, 6, 8, 11;

ENV50204,EN61000-6-2(EN50082-2)

heavy Industry Level, Criteria A

Remote ON/OFF

RC+/RC-: 0~0.8Volts(DC)= power On

4~10Volts(DC)= power Off

ENVIRONMENTAL SPECIFICATIONS

Oper. Temperature

-20°C to +70°C (See Derate Curve)

Storage Temperature

-20°C to +85°C, 10~95% RH

Relative Humidity

20~90% RH non cond

Temperature Coefficient

±0.04% / °C (0-50°C)

MTBF

355KHrs min,MIL-HDBK-217F(25°C)

Vibration

10~500Hz, 2G10min./1cycle, period for

60min. each along X, Y, Z axes

PHYSICAL SPECIFICATIONS

Size

Millimeters

222 x 55 x 30

Inches

8.74” x 2.17 ” x 1.18 ”

Weight

10.58 oz (300g)

NOTE

1. Ripple & noise are measured at 20MHz of bandwidth by using a 12”

twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

2. Tolerance : includes set up tolerance, line regulation and load regula-

tion.

3. 33.3% Duty cycle maximum within every 30 seconds. Average output

power should not exceed the rated power.

All specifications are typical at nominal input, full load, and 25°C unless other-

wise noted