Electronic Components Datasheet Search |
|
BTS740S2 Datasheet(PDF) 6 Page - Infineon Technologies AG |
|
BTS740S2 Datasheet(HTML) 6 Page - Infineon Technologies AG |
6 / 15 page PROFET® BTS 740 S2 Parameter and Conditions, each of the two channels Symbol Values Unit at Tj = -40...+150°C, Vbb = 12 V unless otherwise specified min typ max Semiconductor Group 6 2003-Oct-01 Reverse Battery Reverse battery voltage 15) -Vbb -- -- 32 V Drain-source diode voltage (Vout > Vbb) IL = - 4.0 A, Tj = +150°C -VON -- 600 -- mV Diagnostic Characteristics Current sense ratio16), static on-condition, VIS = 0...5 V, Vbb(on) = 6.517)...27V, kILIS = IL / IIS Tj = -40°C, IL = 5 A: kILIS 4350 4800 5800 Tj= -40°C, IL= 0.5 A: 3100 4800 7800 Tj= 25...+150°C, IL= 5 A: Tj= 25...+150°C, IL = 0.5 A: 4350 3800 4800 4800 5350 6300 Current sense output voltage limitation Tj = -40 ...+150°C IIS = 0, IL = 5 A: VIS(lim) 5.4 6.1 6.9 V Current sense leakage/offset current Tj = -40 ...+150°C VIN=0, VIS = 0, IL = 0: IIS(LL) 0 -- 1 µA VIN=5 V, VIS = 0, IL = 0: IIS(LH) 0 -- 15 VIN=5 V, VIS = 0, VOUT = 0 (short circuit) IIS(SH) 18) 0 -- 10 Current sense settling time to IIS static ±10% after positive input slope18), IL = 0 5 A tson(IS) -- -- 300 µs Current sense settling time to 10% of IIS static after negative input slope18), IL = 5 0 A tsoff(IS) -- 30 100 µs Current sense rise time (60% to 90%) after change of load current18) IL = 2.5 5 A tslc(IS) -- 10 -- µs Open load detection voltage19) (off-condition) VOUT(OL) 2 3 4V Internal output pull down (pin 17,18 to 2 resp. 13,14 to 6), VOUT=5 V RO 5 15 40 k Ω 15 ) Requires a 150 Ω resistor in GND connection. The reverse load current through the intrinsic drain-source diode has to be limited by the connected load. Power dissipation is higher compared to normal operating conditions due to the voltage drop across the drain-source diode. The temperature protection is not active during reverse current operation! Input and Status currents have to be limited (see max. ratings page 3 and circuit page 9). 16) This range for the current sense ratio refers to all devices. The accuracy of the k ILIS can be raised at least by a factor of two by matching the value of k ILIS for every single device. In the case of current limitation the sense current IIS is zero and the diagnostic feedback potential VST is High. See figure 2c, page 12. 17) Valid if Vbb(u rst) was exceeded before. 18) not subject to production test, specified by design 19) External pull up resistor required for open load detection in off state. |
Similar Part No. - BTS740S2 |
|
Similar Description - BTS740S2 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |