PBMPLS Series

D C / A C S I N E W A V E I N V E R T E R

FEATURES

• 500W - 7000W

• True Sinewave Output

• Massive Overload Capability

• High Efficiency Toroidal Transformer

• CCT Breaker/ Batt Isolator Switch

• Chassis and Wall mounting

SPECIFICATIONS

Doc. No. PBMPLS Rev.E 20-01-16

www.powerbox.com.au - 1800 251 380

www.powerbox.co.nz - 0800 104 480

INPUT

Input Voltage

12V, 24V, 48V (Standard)

36V, 72V, 96V, 120V (Also available)

Voltage range

-20% to +45% of nominal..

OUTPUT

Output Voltage

230Vac ±4% (Standard)

110Vac ±4% (Option)

Output Frequency

50/60Hz ±0.1

Output Waveform

True sinewave < 4% THD.

Power factor correction

All conditions.

Crest factor

>4

Load start sensitivity

0-20W

Efficiency

94%Typically

PROTECTION

DC to AC isolation

3500V

Over-load protection

Yes.

Over-temperature protection

Yes.

Short circuit protection

Yes.

Battery under and

over voltage protection

Yes.

Circuit breaker On/Off

The circuit breaker by pushing switch "UP"

the battery supply is connected to the

inverter. The circuit breaker will turn OFF

automatically if too large a load is left on

the inverter continuously. Reset the switch

after allowing approx 5mins to cool. If the

inverter shuts down due to overload,

undervolts or overvolts it can be reset by

turning the circuit breaker OFF, waiting 10

seconds (or until LED goes out). Then

turning it on again.

ENVIRONMENT

Temperature range

-10°C to 50°C

Cooling

Thermostatically controlled 2-speed fan.

STANDARDS & APPROVALS

Safety standards

AS3100, AS3000

C-tick

AS/NZS CISPR14, AS/NZS 1044

EMC standards

AS2279, EN55014

ALARMS & INDICATORS

Inverter Operation

When inverter is switched on all 3 LEDS light up for one

second for system check procedure

Power Indicator

Green LED. Flashes when in standby mode (no load

connected). When load applied LED illuminates

continuously

Undervolts/Overvolts

Red LED. In order to protect the battery the inverter will

shutdown after 5 secs if the battery voltage falls below

its limit (Undervolts) LED remains continous or exceeds

the maximum (Overvolts) LED will continue to flash.

Over temperature

Red LED, If the internal temperature exceeds safe

operating limits for more than 5 secnds, the inverter will

shut down in Over temp with this LED on continuously.

Allow 5mins for the inverter to cool and reset the unit.

Over load

Red LED, if the load demands more current than the

inverter can safely supply for more than 5 seconds, the

inverter will shutdown in Overload and this LED will flash

OPTIONAL FEATURES

CODE

ADD OPTION TO THE END OF INVERTER PART NUMBER

D

RCD fitted in place of hardware junction box of AC output.

G

MIL spec conformal coating applied to final assembly.

R

Ruggedisation for high vibration environment.

K

Automatic transfer switch 25Amp for 1000W to 1800W.

KX

Automatic transfer switch with ON delay

timer and voltage sensing module. 40Amps

for 2000W to 4000W and 65Amp for

5000W to 7000W models.

V

AC output voltage e.g. 100-120Vac.

H

Frequency 60Hz

L

"AC OK" alarm relay contact

C

Twin switched GPO

(available only on 1000W to 5000W models).

D

Twin switched RCD GPO

(available only on 1000W to 5000W models).

MECHANICAL

AC outlet

Single power outlet (500-600W models).

Single power outlet & screw terminal junction box

(1000-1800W models).

Screw terminal junction box (2000-7000W models).

Battery leads

Heavy duty low loss battery leads

Red battery positive, Black battery negative

Dimensions

500-600W: 260x160x100mm

1kw-1.8kw: 330x296x150mm

2kw-3.5kw: 370x386x180mm

4kw-7kw: 475x458x187mm