Electronic Components Datasheet Search |
|
MAX801LMJA Datasheet(PDF) 4 Page - Maxim Integrated Products |
|
MAX801LMJA Datasheet(HTML) 4 Page - Maxim Integrated Products |
4 / 12 page 40 -55 -15 65 VCC SUPPLY CURRENT vs. TEMPERATURE (NORMAL OPERATING MODE) 50 TEMPERATURE (°C) 25 105 -35 45 125 5 85 70 60 45 55 75 65 MAX808 MAX801 3.0 2.5 2.0 1.5 1.0 0.5 0 -60 -20 60 140 BATTERY SUPPLY CURRENT vs. TEMPERATURE (BATTERY-BACKUP MODE) TEMPERATURE (°C) 20 100 -40 40 120 080 6 5 4 3 2 1 0 -60 -20 60 140 MAX808 CHIP-ENABLE PROPAGATION DELAY vs. TEMPERATURE TEMPERATURE (°C) 20 100 -40 40 120 080 8-Pin µP Supervisory Circuits with ±1.5% Reset Accuracy 4 _______________________________________________________________________________________ Note 1: Either VCC or VBATT can go to 0V if the other is greater than 2V. Note 2: The supply current drawn by the MAX80_ from the battery (excluding IOUT) typically goes to 15µA when (VBATT - 0.1V) < VCC < VBATT. In most applications, this is a brief period as VCC falls through this region (see Typical Operating Characteristics). Note 3: “+” = battery-discharging current, “-” = battery-charging current. Note 4: WDI is internally connected to a voltage divider between VCC and GND. If unconnected, WDI is typically driven to 1.8V, disabling the watchdog function. Note 5: The chip-enable resistance is tested with V CE IN = VCC / 2 and ICE IN = 1mA. Note 6: The chip-enable propagation delay is measured from the 50% point at CE IN to the 50% point at CE OUT. Note 7: If CE IN goes high, CE OUT goes high immediately and stays high until reset is deasserted and CE IN is low. ELECTRICAL CHARACTERISTICS (continued) (VCC = 4.6V to 5.5V for the MAX80_L, VCC = 4.5V to 5.5V for the MAX80_N, VCC = 4.35V to 5.5V for the MAX80_M; VBATT = 2.8V; TA = TMIN to TMAX. Typical values are at VCC = 5V and TA = +25°C, unless otherwise noted.) CONDITIONS Enabled mode, VCC = VRST(max) Ω 75 150 CE IN to CE OUT Resistance (Note 5) UNITS MIN TYP MAX SYMBOL PARAMETER VCC = 4.25V, CE OUT = 0V mA 15 CE OUT Short-Circuit Current ( RESET Active) VCC = 5V, CLOAD = 50pF, 50 Ω source-impedance driver ns 38 CE IN to CE OUT Propagation Delay (Note 6) VCC = 4.25V, IOUT = 2mA V 3.5 CE OUT Output Voltage High ( RESET Active) VCC falling, CE IN = 0V µs 18 RESET to CE OUT Delay (Note 7) VCC = 4.25V ±0.00002 ±1 µA CE IN Leakage Current VCC = 0V, IOUT = 10µA VBATT - 0.1 VBATT CHIP-ENABLE GATING (MAX808) CHIP-ENABLE GATING (MAX808) __________________________________________Typical Operating Characteristics (VCC = 5V, VBATT = 2.8V, no load, TA = +25°C, unless otherwise noted.) |
Similar Part No. - MAX801LMJA |
|
Similar Description - MAX801LMJA |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |