Electronic Components Datasheet Search |
|
MAX727ECK Datasheet(PDF) 3 Page - Maxim Integrated Products |
|
MAX727ECK Datasheet(HTML) 3 Page - Maxim Integrated Products |
3 / 4 page 5V/3.3V/3V 2A Step-Down, PWM, Switch-Mode DC-DC Regulators _______________________________________________________________________________________ 3 ELECTRICAL CHARACTERISTICS (continued) (VIN = 25V, Tj = TMIN to TMAX, unless otherwise noted.) Note 1: Do not exceed switch-to-input voltage limitation. Note 2: For switch currents between 1A and 2A, maximum switch-on voltage can be calculated via linear interpolation. Note 3: By setting the SENSE pin to 5.5V, the VC pin is forced to its low clamp level and the switch duty cycle is forced to zero, approximating the zero load condition. Note 4: For proper regulation, total voltage from VIN to GND must be ≥ 8V after start-up. Note 5: To avoid extremely short switch-on times, the switch frequency is internally scaled down when VSENSE is less than 2.6V (MAX727), 2.0V (MAX728), or 1.8V (MAX729). Switch current limit is tested with VSENSE adjusted to give a 1µs minimum switch-on time. Note 6: Guaranteed, not production tested. 0% duty cycle 0% duty cycle VC Voltage Temperature Coefficient mV/°C Thermal Resistance Junction to Case (Note 6) °C/W 4.0 V -4 Tj = TMIN to TMAX VC Voltage 1.5 Tj = +25°C Output Voltage Line Regulation %/V 0.005 0.020 8V ≤ VIN ≤ 40V ±1.0 ±3.0 Tj = TMIN to TMAX VOUT (nominal) = 5V (MAX727), 3.3V (MAX728), or 3V (MAX729); all conditions of input voltage, output voltage, and load current Output Voltage Tolerance % ±0.5 ±2.0 Tj = +25°C MAX729 MAX728 MAX727 MAX729 MAX728 MAX727 CONDITIONS 2.2 3.8 6.5 Tj = +25°C SENSE Pin Divider Resistance 2.5 4.2 7.0 k Ω 3.0 5.0 8.0 2.90 3.00 3.10 VC = 2V SENSE Voltage 3.20 3.30 3.40 V 4.85 5.00 5.15 UNITS MIN TYP MAX PARAMETER ______________________________________________________________Pin Description 5 VIN supplies power to the internal circuitry and also connects to the collector of the internal power switch. VIN must be bypassed with a low-ESR capacitor, typically 200µF or 220µF. Internal Power Switch Output. The Switch output can swing 35V below ground and is rated for 2A. Ground requires a short, low-noise connection to ensure good load regulation. The internal refer- ence is referred to GND, so errors at this pin are multiplied by the error amplifier. Error-Amplifier Output. A series RC network connected to this pin compensates the MAX727/MAX728/MAX729. Output swing is limited to about 5.8V in the positive direction and -0.7V in the negative direction. VC can also synchronize the MAX727/MAX728/MAX729 to an external TTL clock in the 115kHz to 170kHz range. See MAX724/MAX726 data sheet. SENSE Input is the internal error amplifier's input, and should be directly connected to VOUT. SENSE also aids current limiting by reducing oscillator frequency when VOUT is low. 4 3 2 1 PIN VIN VSW GND VC SENSE FUNCTION NAME |
Similar Part No. - MAX727ECK |
|
Similar Description - MAX727ECK |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |