Electronic Components Datasheet Search
  English  ▼
ALLDATASHEET.COM

X  

LT1641 Datasheet(PDF) 5 Page - Linear Technology

Part # LT1641
Description  Positive High Voltage Hot Swap Controller
Download  12 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  LINER [Linear Technology]
Direct Link  http://www.linear.com
Logo LINER - Linear Technology

LT1641 Datasheet(HTML) 5 Page - Linear Technology

  LT1641_15 Datasheet HTML 1Page - Linear Technology LT1641_15 Datasheet HTML 2Page - Linear Technology LT1641_15 Datasheet HTML 3Page - Linear Technology LT1641_15 Datasheet HTML 4Page - Linear Technology LT1641_15 Datasheet HTML 5Page - Linear Technology LT1641_15 Datasheet HTML 6Page - Linear Technology LT1641_15 Datasheet HTML 7Page - Linear Technology LT1641_15 Datasheet HTML 8Page - Linear Technology LT1641_15 Datasheet HTML 9Page - Linear Technology Next Button
Zoom Inzoom in Zoom Outzoom out
 5 / 12 page
background image
5
LT1641
1641fd
PI FU CTIO S
ON (Pin 1): The ON pin is used to implement undervoltage
lockout. When the ON pin is pulled below the 1.233V High-
to-Low threshold voltage, an undervoltage condition is
detected and the GATE pin is pulled low to turn the
MOSFET off. When the ON pin rises above the 1.313V
Low-to-High threshold voltage, the MOSFET is turned on
again.
FB (Pin 2): Power Good Comparator Input. It monitors the
output voltage with an external resistive divider. When the
voltage on the FB pin is lower than the High-to-Low
threshold of 1.233V, the PWRGD pin is pulled low and
released when the FB pin is pulled above the 1.313V Low-
to-High threshold.
The FB pin also effects foldback current limit (see Figure 7
and related discussion).
PWRGD (Pin 3): Open Collector Output to GND. The
PWRGD pin is pulled low whenever the voltage at the FB
pin falls below the High-to-Low threshold voltage. It goes
into a high impedance state when the voltage on the FB pin
exceeds the Low-to-High threshold voltage. An external
pull-up resistor can pull the pin to a voltage higher or lower
than VCC.
GND (Pin 4): Chip Ground.
TIMER (Pin 5): Timing Input. An external timing capacitor
at this pin programs the maximum time the part is allowed
to remain in current limit.
When the part goes into current limit, an 80
µA pull-up
current source starts to charge the timing capacitor. When
the voltage on the TIMER pin reaches 1.233V, the GATE
pin is pulled low; the pull-up current will be turned off and
the capacitor is discharged by a 3
µA pull-down current.
When the TIMER pin falls below 0.5V, the GATE pin turns
on once the ON pin is pulsed low. Use no less than 1.5nF
for the timing capacitor, C2.
By connecting a 0.01
µF capacitor from the GATE pin to the
center tap of a resistive divider at the ON pin, the part
automatically restarts after a current limit fault. With a
short at the output, the part cycles on and off with a 3.75%
on-time duty cycle.
GATE (Pin 6): The High Side Gate Drive for the External
N-Channel. An internal charge pump guarantees at least
10V of gate drive for supply voltages above 20V and 4.5V
gate drive for supply voltages between 10.8V and 20V. The
rising slope of the voltage at the GATE is set by an external
capacitor connected from the GATE pin to GND and an
internal 10
µA pull-up current source from the charge
pump output.
When the current limit is reached, the GATE pin voltage will
be adjusted to maintain a constant voltage across the
sense resistor while the timer capacitor starts to charge.
If the TIMER pin voltage exceeds 1.233V, the GATE pin will
be pulled low.
The GATE pin is pulled to GND whenever the ON pin is
pulled low, the VCC supply voltage drops below the 8.3V
undervoltage lockout threshold or the TIMER pin rises
above 1.233V.
SENSE (Pin 7): The Current Limit Sense Pin. A sense
resistor must be placed in the supply path between VCC
and SENSE. The current limit circuit will regulate the
voltage across the sense resistor (VCC – VSENSE) to 47mV
when VFB is 0.5V or higher. If VFB drops below 0.5V, the
voltage across the sense resistor decreases linearly and
stops at 12mV when VFB is 0V.
To defeat current limit, short the SENSE pin to the VCC pin.
VCC (Pin 8): The Positive Supply Input ranges from 9V to
80V for normal operation. ICC is typically 2mA. An internal
undervoltage lockout circuit disables the chip for inputs
less than 8.3V.


Similar Part No. - LT1641_15

ManufacturerPart #DatasheetDescription
logo
Linear Technology
LT1641-1 LINER-LT1641-1 Datasheet
179Kb / 12P
   Positive High Voltage Hot Swap Controllers
LT1641-1 LINER-LT1641-1 Datasheet
322Kb / 40P
   Hot Swap Controller
LT1641-1 LINER-LT1641-1 Datasheet
319Kb / 36P
   Negative Voltage Hot Swap Controllers
LT1641-1 LINER-LT1641-1 Datasheet
310Kb / 34P
   ??8V Hot Swap Controllers
LT1641-1 LINER-LT1641-1 Datasheet
185Kb / 12P
   Positive High Voltage Hot Swap Controllers
More results

Similar Description - LT1641_15

ManufacturerPart #DatasheetDescription
logo
Linear Technology
LT1641 LINER-LT1641 Datasheet
187Kb / 12P
   Positive High Voltage Hot Swap Controller
logo
Texas Instruments
TPS2490 TI1-TPS2490_17 Datasheet
1Mb / 36P
[Old version datasheet]   Positive High-Voltage Power-Limiting Hot Swap Controller
logo
Micrel Semiconductor
MIC2587 MICREL-MIC2587 Datasheet
536Kb / 16P
   Single-Channel, Positive High-Voltage Hot Swap Controller
MIC2587 MICREL-MIC2587_13 Datasheet
1,007Kb / 22P
   Single-Channel, Positive High-Voltage Hot Swap Controller
logo
Maxim Integrated Produc...
MAX5933A MAXIM-MAX5933A Datasheet
269Kb / 15P
   Positive High-Voltage, Hot-Swap Controllers
Rev 1; 7/04
logo
Micrel Semiconductor
MIC2586 MICREL-MIC2586 Datasheet
601Kb / 17P
   Single-Channel, Positive High-Voltage Hot Swap Controller/Sequencer
logo
Linear Technology
LT4256-2 LINER-LT4256-2_15 Datasheet
219Kb / 16P
   Positive High Voltage Hot Swap Controllers
LT1641-1 LINER-LT1641-1 Datasheet
179Kb / 12P
   Positive High Voltage Hot Swap Controllers
LT4256-1 LINER-LT4256-1_15 Datasheet
219Kb / 16P
   Positive High Voltage Hot Swap Controllers
LT1641-1 LINER-LT1641-1_15 Datasheet
185Kb / 12P
   Positive High Voltage Hot Swap Controllers
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12


Datasheet Download

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com