Electronic Components Datasheet Search |
|
HS9-565ARH-T Datasheet(PDF) 5 Page - Intersil Corporation |
|
HS9-565ARH-T Datasheet(HTML) 5 Page - Intersil Corporation |
5 / 6 page 5 Other Considerations Grounds The HS-565ARH-T has two ground terminals, pin 5 (REF GND) and pin 12 (PWR GND). These should not be tied together near the package unless that point is also the system signal ground to which all returns are connected. (If such a point exists, then separate paths are required to pins 5 and 12). The current through pin 5 is near zero DC (Note); but pin 12 carries up to 1.75mA of code - dependent current from bits 1, 2, and 3. The general rule is to connect pin 5 directly to the system “quiet” point, usually called signal or analog ground. Connect pin 12 to the local digital or power ground. Then, of course, a single path must connect the analog/signal and digital/power grounds. NOTE: Current cancellation is a two step process within the HS- 565ARH-T in which code dependent variations are eliminated, the re- sulting DC current is supplied internally. First an auxiliary 9-bit R-2R ladder is driven by the complement of the DACs input code. Together, the main and auxiliary ladders draw a continuous 2.25mA from the internal ground node, regardless of input code. Part of the DC current is supplied by the zener voltage reference, and the remainder is sourced from the positive supply via a current mirror which is laser trimmed for zero current through the external terminal (pin 5). Layout Connections to pin 9 (IOUT) on the HS-565ARH-T are most critical for high speed performance. Output capacitance of the DAC is only 20pF, so a small change of additional capacitance may alter the op amp’s stability and affect settling time. Connections to pin 9 should be short and few. Component leads should be short on the side connecting to pin 9 (as for feedback capacitor C). See the Settling Time Section. Bypass Capacitors Power supply bypass capacitors on the op amp will serve the HS-565ARH-T also. If no op amp is used, a 0.01mF ceramic capacitor from each supply terminal to pin 12 is sufficient, since supply current variations are small. Bipolar (See Figure 2) ±10V NC VO 1.69K All 0’s All 1’s R3 R4 -10V +9.99512V ±5V VO Pin 10 1.43K All 0’s All 1’s R3 R4 -5V +4.99756V ±2.5V VO Pin 9 1.1K All 0’s All 1’s R3 R4 -2.5V +2.49878V FIGURE 3A. FIGURE 3B. TABLE 1. OPERATING MODES AND CALIBRATION (Continued) MODE CIRCUIT CONNECTIONS CALIBRATION OUTPUT RANGE PIN 10 TO PIN 11 TO RESISTOR (R) APPLY INPUT CODE ADJUST TO SET VO VLSB SUPPLY 0.1 µF DVM COMPARATOR OUT B C 10 90 200K + - 5 9 10 NC 11 8 2.5K 5K 5K 20V ± 20% BIAS TURN ON TURN OFF 9.95K 2mA 12 HS-565ARH-T D OUT 14 13 23 24 . . . . . . . . . . . . . 5V P SYNC IN TRIG OUT OUT A ~100 kHz STROBE IN LSB PULSE GENERATOR NO. 2 PULSE GENERATOR NO. 2 50% DIGITAL INPUT DAC OUTPUT COMP. STROBE COMP. OUT “EQUAL BRIGHTNESS” +3V 0V 0V -400mV 2V 0.8V 4V 0V (TURN OFF) A B C D 50% tX tD = COMPARATOR DELAY SETTLING TIME -0.50LSB HS-565ARH-T |
Similar Part No. - HS9-565ARH-T |
|
Similar Description - HS9-565ARH-T |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |