Electronic Components Datasheet Search |
|
IDT72255L25G Datasheet(PDF) 10 Page - Integrated Device Technology |
|
IDT72255L25G Datasheet(HTML) 10 Page - Integrated Device Technology |
10 / 30 page 10 MILITARY AND COMMERCIAL TEMPERATURE RANGES IDT72255/72265 SyncFIFO ™ 8,192 x 18, 16,384 x 18 two pointers operate independently; however, a read and a write should not be performed simultaneously to the offset registers. A Master Reset initializes both pointers to the Empty Offset (LSB) register. A Partial Reset has no effect on the position of these pointers. Once serial offset loading has been selected, then pro- gramming PAE and PAF procedes as follows: When LD and SEN are set LOW, data on the SI input are written, one bit for each WCLK rising edge, starting with the Empty Offset (13 bits for the 72255, 14 bits for the 72265), ending with the Full Offset (13 bits for the 72255, 14 bits for the 72265). A total of 26 bits are necessary to program the 72255; a total of 28 bits are necessary to program the 72265. Individual registers cannot be loaded serially; rather, both must be programmed in sequence, no padding allowed. PAE and PAF can show a valid status only after the the full set of bits have been entered. The registers can be re-programmed, as long as both offsets are loaded. When LD is LOW and SEN is HIGH, no serial write to the registers can occur. Once parallel offset loading has been selected, then programming PAE and PAF procedes as follows: When LD and WEN are set LOW, data on the inputs Dn are written into the Empty Offset Register on the first LOW-to-HIGH transition of WCLK. Upon the second LOW-to-HIGH transition of WCLK, data at the inputs are written into the Full Register. The third transition of WCLK writes, once again, to the Empty Offset Register. To ensure proper programming (serial or parallel) of the offset registers, no read operation is permitted from the time of reset (master or partial) to the time of programming. (During this period, the read pointer must be pointing to the first location of the memory array.) After the programming has been accomplished, read operations may begin. Write operations to memory are allowed before and during the parallel programming sequence. In this case, the pro- gramming of all offset registers does not have to occur at one time. One or two offset registers can be written to and then, by bringing LD HIGH, write operations can be redirected to the FIFO memory. When LD is set LOW again, and WEN is LOW, the next offset register in sequence is written to. As an alternative to holding WEN LOW and toggling LD, parallel programming can also be interrupted by setting LD LOW and toggling WEN. Write operations to memory are allowed before and during the serial programming sequence. In this case, the program- ming of all offset bits does not have to occur at once. A select number of bits can be written to the SI input and then, by bringing LD and SEN HIGH, data can be written to FIFO memory via Dn by toggling WEN. When WEN is brought HIGH with LD and SEN restored to a LOW, the next offset bit in sequence is written to the registers via SI. If a mere interuption of serial programming is desired, it is sufficient either to set LD LOW and deactivate SEN or to set SEN LOW and deactivate LD. Once LD and SEN are both restored to a LOW level, serial offset programming continues from where it left off. Note that the status of a partial flag ( PAE or PAF) output is invalid during the programming process. From the time parallel programming has begun, a partial flag output will not be valid until the appropriate offset word has been written to the register pertaining to that flag. From the time serial programming has begun, neither partial flag will be valid until the full set of bits required to fill all the offset registers has been written. Measuring from the rising WCLK edge that achieves either of the above criteria; PAF will be valid after two more rising WCLK edges plus tPAF, PAE will will be valid after the next two rising RCLK edges plus tPAE (Add one more RCLK cycle if tSKEW2 is not met.) The act of reading the offset registers employs a dedicated read offset register pointer. The contents of the offset registers can be read on the output lines when LD is set LOW and REN is set LOW; then, data are read via Qn from the Empty Offset Register on the first LOW-to-HIGH transition of RCLK. Upon the second LOW-to-HIGH transition of RCLK, data are read from the Full Offset Register. The third transition of RCLK, reads, once again, from the Empty Offset Register. It is permissable to interrupt the the offset register access sequence with reads or writes to memory . The interruption is accomplished by deasserting REN, LD, or both together. When REN and LD are restored to a LOW level, access of the registers continues where it left off. LD functions the same way in both IDT Standard and FWFT modes. FREQUENCY SELECT INPUT (FS) An internal state machine manages the movement of data through the SuperSync FIFO. The FS line determines whether RCLK or WCLK will synchronize the state machine. Tie FS to VCC if the RCLK line is running at a lower frequency than the WCLK line. In this case, the state machine will be synchro- nized to WCLK. Tie FS to GND if the RCLK line is running at a higher frequency than the WCLK line. In this case, the state machine will be synchronized to RCLK. Note that FS must be set so the clock line running at the higher frequency drives the state machine; this ensures efficient handling of the data within the FIFO. If the same clock signal drives both the WCLK and the RCLK pins, then tie FS to GND. The frequency of the clock tied to the state machine (referred to as the "selected clock") may be changed at any time, so long as it is always greater than or equal to the frequency of the clock that is not tied to the state machine (referred to as the "non-selected clock"). The frequency of the non-selected clock can also be varied with time, so long as it never exceeds the frequency of the selected clock. To be more specific, the frequencies of both RCLK and WCLK may be varied during FIFO operation, provided that, at any given point in time, the cycle period of the selected clock is equal to or less than the cycle period of the non-selected clock. The selected clock must be continuous. It is, however, permissible to stop the non-selected clock. Note, so long as RCLK is idle, EF/OR and PAE will not be updated. Likewise, as long as WCLK is idle, FF/IR and PAF will not be updated. Changing the FS setting during FIFO operation (i.e. read- ing or writing) is not permitted; however, such a change at the time of Master Reset or Partial Reset is all right. FS is an asynchronous input. |
Similar Part No. - IDT72255L25G |
|
Similar Description - IDT72255L25G |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |