Electronic Components Datasheet Search |
|
SRX803XR2I000PD Datasheet(PDF) 3 Page - OPLINK Communications Inc. |
|
SRX803XR2I000PD Datasheet(HTML) 3 Page - OPLINK Communications Inc. |
3 / 3 page Oplink Communications, Inc. reserves the right to make changes in equipment design or specifications without notice. Information supplied by Oplink Commu- nications, Inc. is believed to be accurate and reliable. However, no responsibility is assumed by Oplink Communications, Inc. for its use nor for any infringements of third parties, which may result from its use. No license is granted by implication or otherwise under any patent right of Oplink Communications, Inc. © 2008, Oplink Communications, Inc. Application Notes The receiver converts the incident optical power to a photocurrent via a high performance avalanche photodiode (APD).The photocurrent can be monitored via the differential voltage across the two VPM+ and VPM- output pins. It is important to note that the common mode voltage (i.e. DC voltages at PM+ and VPM-) is high (-60V typical). The APD bias voltage is temperature compensated to ensure stable operation over the entire operating temperature range. The APD bias voltage is also available as an output via the VPD output. The maximum current that this output can source is 1mA. The signal detect circuit monitors the level of the incoming optical signal and generates a logic LOW signal when an insufficient photocurrent is produced. Both differential DATA+ and DATA- outputs (also SIGNAL DETECT+ and SIGNAL DETECT- if the PECL option is chosen) are open emitter PECL levels requiring termination (50Ω to VCC - 2V or 510Ω to GND is recommended). Both differential outputs should be terminated in the same manner, even if only one is used. If the TTL option is chosen for the SIGNAL DETECT outputs, no termination resistor should be used. The power supply line should be wellfiltered. The power supply should be bypassed by 0.01 or 0.1μF ceramic chip placed as close to the receiver module as possible. Related Transmitter & Receiver Modules STX-03: OC-3/STM-1 Transmitter (multi-sourced 20-pin DIP) SRX-03: OC-3/STM-1 Receiver without Clock Recovery, ECL SIGNAL DETECT (multi-sourced 20-pin DIP) SRC-03: OC-3/STM-1 Receiver with Clock Recovery (multi-sourced 20-pin DIP) SRC-03-S: OC-3/STM-1 Receiver with Clock Recovery (24-pin DIP, compatible with Sumitomo SDT8701-RD) The pigtail length from the package edge is 1.0 meter typical. Ordering Information SRX03-APD R4. 2008.04.30 3 SRX 0 0 0 3 X R 2 8 0 Supply Voltage RX only 5V= 8 Temperature Range Connector Type & Option Pigtail FC, SD-TTL= PA Pigtail ST, SD-TTL= PB Pigtail SC, SD-TTL= P5 Pigtail FC, SD-PECL= PC Pigtail ST, SD-PECL= PD Pigtail SC, SD-PECL= P4 -40 ~85˚C= I 0~70˚C= H APD VPM- VPM+ VPD OUT APD Bias 220Ω 10kΩ 10kΩ Supply Package Outline Dimensions in inches [mm] Default tolerances: .xxx = ± .005”, .xx = ± .01” Receivers Wavelength Range 1100~1600nm APD |
Similar Part No. - SRX803XR2I000PD |
|
Similar Description - SRX803XR2I000PD |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |