Electronic Components Datasheet Search |
|
TD102-EX-485 Datasheet(PDF) 2 Page - MORNSUN Science& Technology Ltd. |
|
TD102-EX-485 Datasheet(HTML) 2 Page - MORNSUN Science& Technology Ltd. |
2 / 4 page The copyright and authority for the interpretation of the products are reserved by MORNSUN TD10x-EX-485 2013.07.01-A/1 Page 2 of 4 EXPLOSION PROTECTION Explosion Protection Mark [Exia Ga] II C Between the pin 9 and 10, 15 and 16 Uo=11.2 V, Io=12mA, Po= 33mW, Um=250V Co=1.2 μF, Lo=2mH Certification Parameters Between the pin 9 and 1 Uo=12.6V, Io=306mA, Po=0.96W, Um=250V Co=0.7 μF, Lo=0.21mH Explosion protection certification agency CHINA NATIONAL QUALITY SUPERVISION AND TEST CENTRE FOR EXPLOSION PROTECTED ELECTRICAL PRODUCTS CNEx 12.2419(TD103-EX-485) Explosion qualified NO. CNEx 12.2420(TD102-EX-485) ISOLATION POWER OUTPUT CURVE 5V/6V Isolation power output curve 0 1 2 3 4 5 6 7 0 30 60 90 120 Output Current Io(mA) 5V 6V 8V/9V/12V Isolation power output curve 0 2 4 6 8 10 12 14 0 20 40 60 80 Output Current Io(mA) 8V 9V 12V CONNECTION 1. Rem ovable terminal; 2. Cross section area of wiring: 0.5mm 2 ~2.5 mm2; 3. The length of bare wire is about 8mm, locked up by the M3 bolt. Selection guidelines for intrinsically safe explosion protection system 1. The explosion protection grade of the barrier must be not less than that of intrinsically safe explosion protection device in spot. 2. Take inconsideration of hazardous end output resistance and loop resistance make sure the barrier output voltage meets the minimum operation voltage requirement of intrinsically safe device in spot. 3. The safety parameters about intrinsically safe end meets: Uo ≤ UI, Io ≤ Iin, Po ≤ Pin Co ≥ Cin, Lo ≥ Lin 4. Select suitable safety barrier which matches the intrinsically safe device in spot according to the power polarity, signal type and transmission mode about the device. 5. Much more protection is required, which can avoid the influence of the leakage current generated by safety barrier on intrinsically safe device in spot. 6. The wires leading to dangerous field should be constrainted in blue intrinsically safe wires, and its copper cross-section should be more than 0.5mm 2; Insulation intensity should be more than 500VDC. Operation notes 1. Please read the user manual carefully before using. If any question please contact our technical support department. 2. Please do not use this product in hazardous area. 3. The power supply of this product should be 24VDC power source. It is forbidden to use 220VAC power supply. 4. To avoid invalid explosion protection function, or any failure, users disassemble this product is forbidden. After service 1. Products are carefully inspected and controlled before going out from our factory. If they operated abnormally or there were anything wrong in the inner parts, please contact with our agents near you or technical support in our company as soon as possible. 2. 3 years warranty since the delivery date. During the period of quality guarantee, our company will repair or change free of charge if product has any quality problem in the process of normally using. |
Similar Part No. - TD102-EX-485 |
|
Similar Description - TD102-EX-485 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |