Electronic Components Datasheet Search |
|
BD81A34MUV-M Datasheet(PDF) 8 Page - Rohm |
|
BD81A34MUV-M Datasheet(HTML) 8 Page - Rohm |
8 / 36 page 8/33 Datasheet Datasheet BD81A34MUV-M BD81A34EFV-M TSZ02201-0G3G0C600020-1-2 © 2014 ROHM Co., Ltd. All rights reserved. 16.Jan.2014 Rev.002 www.rohm.com TSZ22111 ・15・001 80 90 100 110 120 -40 -25 -10 5 20 35 50 65 80 95 110 125 Ta [ ℃] Ta vs ILED ⊿VOUT=50mV ⊿VOUT=100mV ⊿VOUT=200mV Description of Blocks 1. Voltage Reference (VREG) 5V (Typ) is generated from the VCC Input Voltage (when at EN=High). This voltage (VREG) is used as power supply of internal circuit and when fixing the pins outside of the IC at a high voltage, as well. The UVLO protection is integrated in VREG. The circuit starts to operate at VCC ≧4.0V (Typ) and VREG=3.5V (Typ) and stops when at VCC≤3.5V (Typ) or VREG≤2.0V (Typ). For release/cancellation condition and detection condition, please refer to Table 2 on page 11. Connect a capacitor (CREG=2.2μF)(typ) to VREG terminal for phase compensation. If the CREG is not connected, the operation of circuit will be notably unstable. 2. Constant Current Driver Table1. LED Control Logic LEDEN1 LEDEN2 LED1 LED2 LED3 LED4 L L ON ON ON ON H L ON ON ON OFF L H ON ON OFF OFF H H ON OFF OFF OFF If less than four constant-current drivers are used, please make the LED1~4 terminal ‘open’ while the output ‘OFF’ by LEDEN1 and LEDEN2 terminal. The truth table for these pins is shown above. If the unused constant-current driver output will be set open without the process of LEDEN1,2 terminals, the ‘open detection’ will be activated. The LEDEN1, 2 terminals is pulled down internally in the IC and it is low at ‘open’ condition. However, they should be connected to VREG terminal or fixed to logic HIGH when in use. (1) Output Current Setting Figure 12. ILED vs RISET The Output Current ILED can be obtained by the following equation: <Precaution During Current Setting> If the output current ILED is set to >100mA/ch, the stability of LED current within specified operating temperature range will decrease. LED current supply value will depend on the amount of ripple in output voltage (VOUT). The figure below shows the temperature and the possible LED current maximum value setting, please adjust the ripple voltage in such a way that the LED current value setting will fall within the range as shown on the graph below. ( ∆VOUT:Output Ripple Voltage) Figure 13. Temperature (Ta) vs Output LED Current (ILED) : () Typ GAIN 5000 = [] [] ( ) GAIN k R V mA I ISET LED × Ω = 0 . 1 |
Similar Part No. - BD81A34MUV-M |
|
Similar Description - BD81A34MUV-M |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |