Electronic Components Datasheet Search |
|
B1514RW Datasheet(PDF) 2 Page - MicroPower Direct, LLC |
|
B1514RW Datasheet(HTML) 2 Page - MicroPower Direct, LLC |
2 / 2 page Model Number Input Reflected Ripple Current (mA, Typ) Output Over Voltage Protection (VDC) Efficiency (%, Typ) Capacitive Load (µF Max) Fuse Rating Slow-Blow (mA) Voltage (VDC) Current (mA) Voltage (VDC) Current (mA, Max) Current (mA, Min) Nominal Range Full-Load No-Load B1501RW 12 9.0 - 18.0 1,056 30 50 3.3 3,000.0 300.0 3.9 78 470 3,000 B1502RW 12 9.0 - 18.0 1,543 30 50 5.0 3,000.0 300.0 6.8 81 470 3,000 B1503RW 12 9.0 - 18.0 1,452 30 50 12.0 1,250.0 125.0 15.0 86 470 3,000 B1504RW 12 9.0 - 18.0 1,452 30 50 15.0 1,000.0 100.0 18.0 86 470 3,000 B1505RW 12 9.0 - 18.0 1,452 30 50 ±12.0 ±625.0 ±62.5 ±15.0 86 ±220 3,000 B1506RW 12 9.0 - 18.0 1,452 30 50 ±15.0 ±500.0 ±50.0 ±18.0 86 ±220 3,000 B1511RW 24 18.0 - 36.0 528 17 40 3.3 3,000.0 300.0 3.9 78 470 1,500 B1512RW 24 18.0 - 36.0 772 17 40 5.0 3,000.0 300.0 6.8 81 470 1,500 B1513RW 24 18.0 - 36.0 726 17 40 12.0 1,250.0 125.0 15.0 86 470 1,500 B1514RW 24 18.0 - 36.0 726 17 40 15.0 1,000.0 100.0 18.0 86 470 1,500 B1515RW 24 18.0 - 36.0 726 17 40 ±12.0 ±625.0 ±62.5 ±15.0 86 ±220 1,500 B1516RW 24 18.0 - 36.0 726 17 40 ±15.0 ±500.0 ±50.0 ±18.0 86 ±220 1,500 B1521RW 48 36.0 - 75.0 264 10 30 3.3 3,000.0 300.0 3.9 78 470 750 B1522RW 48 36.0 - 75.0 385 10 30 5.0 3,000.0 300.0 6.8 81 470 750 B1523RW 48 36.0 - 75.0 363 10 30 12.0 1,250.0 125.0 15.0 86 470 750 B1524RW 48 36.0 - 75.0 363 10 30 15.0 1,000.0 100.0 18.0 86 470 750 B1525RW 48 36.0 - 75.0 363 10 30 ±12.0 ±625.0 ±62.5 ±15.0 86 ±220 750 B1526RW 48 36.0 - 75.0 363 10 30 ±15.0 ±500.0 ±50.0 ±18.0 86 ±220 750 Model Selection Guide Mechanical Dimensions Notes: 1. An internal filter that complies with EN55022 Class “A” is available. Add a suffix “-F” to the model number. 2. When measuring output ripple, it is recommended that an external 4.7 µF ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. 3. Transient recovery is measured to within a 1% error band for a load step change of 75% to 100%. 4. The maximum control current at the on/off pin (pin 6) during a logic high is 50 µA. The maximum control current to the on/off pin at logic low is -1 mA. If the on/off pin is left open, the unit operates. If it is grounded, the unit will shut off. 5. Operation at no-load will not damage these units. However, they may not meet all specifications. 6. Dual output units may be connected to provide a 10 VDC, 24 VDC or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common. 7. The converter should be connected to a low ac-impedance source. An input source with a highly inductive impedance may affect the stability of the converter. In applications where the converter output loading is high and input power is supplied over long lines, it may be necessary to use a capacitor on the input to insure start-up. In this case, it is recommended that a low Equivalent Series Resistance (ESR <1.0 at 100 kHz) capacitor be mounted close to the converter. A 10.0 µF is recommended. 8. It is recommended that a fuse be used on the input of a power supply for protection. See the table above for the correct rating. Heatsink Notes: • Use of the heatsink will extend the units operating temperature range by approximately 10°C. • The heatsink is black anodized aluminum. MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com Heatsink Dimensions (Optional) For heatsink option, add suffix “H” to model number (i.e. B1503RW-H) www.micropowerdirect.com For Remote Control option, add suffix “R” to model number (i.e. B1503RW-R) Mechanical Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) Pin Single Dual 1 +Vin +Vin 2 -Vin -Vin 3 +Vout +Vout 4 No Pin Comm. 5 -Vout -Vout 6 ON/OFF ON/OFF Pin Connections Derating Curve For Class “A” filter option, add suffix “F” to model number (i.e. B1503RW-F) |
Similar Part No. - B1514RW |
|
Similar Description - B1514RW |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |