Electronic Components Datasheet Search |
|
IRUH3301A1BPB Datasheet(PDF) 4 Page - International Rectifier |
|
IRUH3301A1BPB Datasheet(HTML) 4 Page - International Rectifier |
4 / 9 page 4 www.irf.com IRUH330133BK IRUH330133BP Application Information IRUH3301xxxx 0.1uF and 1uF Ceramic; Two 100uF Low ESR Tantalum V IN GND SHDN V SENSE V OUT 0.1uF and 1uF Ceramic; Two 100uF Low ESR Tantalum Input Voltage Output Voltage Fig. 1. Typical Regulator Circuit; Note the SHDN Pin is hardwired in the “ON” position. The V SENSE Pin is connected as noted in the “General Layout Rules” section. Over-Current & Over-Temperature Protection The IRUH3301 series provides over-current protection by means of a timed latch function. Drive current to the internal PNP pass transistor is limited by an internal resistor (Rb in Fig. 3) between the base of the transistor and the control IC drive FET. If an over-current condition forces the voltage across this resistor to exceed 0.5V (nom), the latch feature will be triggered. The time-to- latch (t LATCH) is nominally 10ms. If the over-current condition exists for less than tLATCH , the latch will not be set. If the latch is set the drive current to the PNP pass transistor will be disabled. The latch will remain set until one of the following actions occur: 1. The SHDN Pin voltage is brought above 1.2V and then lowered below 0.8V. 2. The V IN Pin voltage is lowered below 1.7V. If the junction temperature of the regulator IC exceeds 140°C nominal, the thermal shutdown circuit will set the internal latch and disable the drive current to the PNP pass transistor as described above. After the junction temperature falls below a nominal 125°C, the latch can be reset using either of the actions described above. Under-Voltage Lock-Out The under-voltage lock-out (UVLO) function prevents operation when V IN is less than 1.7V (nominal). There is a nominal 100mV hysteresis about this point. Input Voltage Range The device control functions fully when V IN is greater than 2.8V. The device enters into under- voltage lock-out when V IN < 1.7V (nominal). When 1.7V (nominal) < VIN < 3.7V, VOUT will track VIN and overshoot may occur. A larger output capacitor should be used to slow down the V OUT rise rate for slow V IN ramp applications. Shutdown (SHDN) The regulator can be shutdown by applying a voltage of >1.2V to the SHDN Pin. The regulator will restart when the SHDN Pin is pulled below the shutdown threshold of 0.8V. If the remote shutdown feature is not required, the SHDN Pin should be connected to GND. |
Similar Part No. - IRUH3301A1BPB |
|
Similar Description - IRUH3301A1BPB |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |