Electronic Components Datasheet Search |
|
D5001R803R3PBAEM Datasheet(PDF) 5 Page - International Rectifier |
|
D5001R803R3PBAEM Datasheet(HTML) 5 Page - International Rectifier |
5 / 10 page www.irf.com 5 (26 TO 55V Input, Regulated Dual Outputs) (+1.8V and +3.3V) D5001R803R3P Electrical Performance Characteristics (continued) Notes: Specification and Electrical Performance Characteristics 1. Parameter is tested as part of design characterization or after design changes. Thereafter, parameter shall be guaranteed to the limits specified. 2. Parameter verified during line and load regulation tests. 3. Guaranteed for a D.C. to 20MHz bandwidth. Tested using a 20KHz to 10MHz bandwidth. 4. Capacitive load may be any value from 0 to the maximum limit without compromising dc performance. A capacitive load in excess of the maximum limit may interfere with the proper operation of the converter’s overload protection, causing erratic behavior during turn-on. 5. Overload power dissipation is defined as the device power dissipation with the load set such that both outputs are in a short circuit mode. 6. Load step transition time ≤ 10 µsec. 7. Recovery time is measured from the initiation of the transient to where VOUT has returned to within ±1% of its steady state value. 8. Line step transition time ≤100 µsec. 9. Turn-on delay time from either a step application of input power or a logic low to a logic high transition on the inhibit pin (pin 6) to the point where VOUT = 90% of nominal. 10. Current limit point expressed as a percentage of full rated load current. 11. For models with two positive outputs the envelope specification for the design is that each output voltage is limited to the range 1V to 5V. 12. Although operation at temperatures between +85°C and +125°C is guaranteed, no parameter limits are specified. 13. Meets the derating requirements of EEE-INST-002 – except for ceramic capacitors with voltage stress below 10V will minimum be rated at 50V and a minimum load of 20mA on each output. Limits Parameter Group A Subgroup Conditions -55 °C ≤ TC ≤ +85°C VIN = 42V DC ± 5%, CL = 0 unless otherwise specified Min Nom Max Unit EMC conducted susceptibility (Line rejection) 1 IOUT = 100% rated load Primary power sine wave injection of 2Vp-p, 100Hz to 50MHz, Note 1 80 90 dB Electromagnetic Interference (EMI), conducted emission (CE) 1 IOUT = 100% rated load, Note 1 Limits per Figure 1 Isolation 1 Input to Output or Any Pin to Case except pin 3, test @ 50VDC 100 M Ω Device Weight 55 g MTBF MIL-HDBK-217F2, SF, 35 °C 1 x 10 5 hours |
Similar Part No. - D5001R803R3PBAEM |
|
Similar Description - D5001R803R3PBAEM |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |