Electronic Components Datasheet Search |
|
ATF1508AS-7JC84 Datasheet(PDF) 7 Page - ATMEL Corporation |
|
ATF1508AS-7JC84 Datasheet(HTML) 7 Page - ATMEL Corporation |
7 / 22 page ATF1508AS/Z 7 All ATF1508s also have an optional power down mode. In this mode, current drops to below 10 mA. When the power down option is selected, either PD1 or PD2 pins (or both) can be used to power down the part. The power down option is selected in the design source file. When enabled, the device goes into power down when either PD1 or PD2 is high. In the power down mode, all internal logic signals are latched and held, as are any enabled outputs. All pin transitions are ignored until the PD pin is brought low. When the power down feature is enabled, the PD1 or PD2 pin cannot be used as a logic input or output. How- ever, the pin’s macrocell may still be used to generate bur- ied foldback and cascade logic signals. All Power-Down AC Characteristic parameters are com- puted from external input or I/O pins, with Reduced Power Bit turned on. For macrocells in reduced-power mode (Reduced power bit turned on), the reduced power adder, tRPA, must be added to the AC parameters, which include the data paths t LAD, tLAC, tIC, tACL, tACH and tSEXP. Each output also has individual slew rate control. This may be used to reduce system noise by slowing down outputs that do not need to operate at maximum speed. Outputs default to slow switching, and may be specified as fast switching in the design file. Design Software Support ATF1508AS designs are supported by several third party tools. Automated fitters allow logic synthesis using a variety of high level description languages and formats. Power Up Reset The ATF1508AS has a power-up reset option at two differ- ent voltage trip levels when the device is being powered down. Within the fitter, or during a conversion, if the “power-reset” option is turned “on” ( which is the default option), the trip levels during power up or power down is at 2.8V. The user can change this default option from “on” to “off” (within the fitter or specify it as a switch during conver- sion). When this is done, the voltage trip level during power-down changes from 2.8V to 0.7V. This is to ensure a robust operating environment. The registers in the ATF1508AS are designed to reset dur- ing power up. At a point delayed slightly from V CC crossing V RST, all registers will be reset to the low state. The output state will depend on the polarity of the buffer. This feature is critical for state machine initialization. How- ever, due to the asynchronous nature of reset and the uncertainty of how V CC actually rises in the system, the fol- lowing conditions are required: 1. The V CC rise must be monotonic, 2. After reset occurs, all input and feedback setup times must be met before driving the clock pin high, and, 3. The clock must remain stable during T PR. Security Fuse Usage A single fuse is provided to prevent unauthorized copying of the ATF1508AS fuse patterns. Once programmed, fuse verify is inhibited. However, User Signature and device ID remains accessible. Programming ATF1508AS devices are In-System Programmable (ISP) devices utilizing the 4-pin JTAG protocol. This capability eliminates package handling normally required for program and facilitates rapid design iterations and field changes. Atmel provides ISP hardware and software to allow pro- gramming of the ATF1508AS via the PC. ISP is perfomed by using either a download cable, or a comparable board tester or a simple microprocessor interface. To facilitate ISP programming by the Automated Test Equipment (ATE) vendors, Serial Vector Format (SVF) files can be created by Atmel provided Software utilities. ATF1508AS devices can also be programmed using stan- dard 3rd party programmers. With 3rd party programmer the JTAG ISP port can be disabled thereby allowing 4 addi- tional I/O pins to be used for logic. Contact your local Atmel representatives or Atmel PLD applications for details. ISP Programming Protection The ATF1508AS has a special feature which locks the device and prevents the inputs and I/O from driving if the programming process is interrupted due to any reason. The inputs and I/O default to high-Z state during such a condi- tion. In addition the pin keeper option preserves the former state during device programming. All ATF1508AS devices are initially shipped in the erased state thereby making them ready to use for ISP. Note: For more information refer to the “Desigining for In-Sys- tem Programmability with Atmel CPLDs” application note. |
Similar Part No. - ATF1508AS-7JC84 |
|
Similar Description - ATF1508AS-7JC84 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |