Electronic Components Datasheet Search |
|
TS19453CS-RLG Datasheet(PDF) 4 Page - Taiwan Semiconductor Company, Ltd |
|
TS19453CS-RLG Datasheet(HTML) 4 Page - Taiwan Semiconductor Company, Ltd |
4 / 7 page Preliminary TS19453 AC/DC Programmable Current WLED Driver w/PWM Dimming Control 4/7 Version: Preliminary Application Information (Continue) L is the inductance value, and CL is the coil capacitance. Charging and discharging this capacitance every switching cycle causes high-current spikes in the LED string. Therefore, connecting a small capacitor CO(~100nF) is recommended to bypass these spikes. Using an ultra-fast rectifier diode for D1 is recommended to achieve high efficiency and reduce the risk of false triggering of the current sense comparator. Using diodes with shorter reverse recovery time trr and lower junction capacitance CJ achieves better performance. The reverse voltage rating VR of the diode must be greater than the maximum input voltage of LED lamps. The total parasitic capacitance present at the Drain pin of the TS19453 can be calculated as: CP = CDRAIN + CPCB + CL + CJ When the switching MOSFET turns on, the capacitance CP is discharged into the Drain pin of the IC. The discharge current is limited to about 50mA typically. However, it may become lower at increased junction temperature. The duration of the leading edge current spike can be estimated as: TPSIKE = ((VIN x CP) / (ISAT)) + trr In order to avoid false trigger of the current sense comparator, CP must be minimized in accordance with the following expression. CP =< (Isat * ( TBLANK(min) - trr )) / Vin(max) When TBLANK(min) is the minimum blanking time of 200nS, and Vin(max) is the maximum instantaneous input voltage. Estimating Power Loss Discharging the parasitic capacitance CP in the the Drain output of TS19453 is responsible for the bulk of the switching power loss. It can be estimated using as: PSWITCH = ((CP * VIN 2 / 2 ) + (V IN * ISAT * trr)) * FS FS is the switching frequency and is the saturated Drain current of TS19453, the switching loss is the greatest at the maximum input voltage. Disregarding the voltage drop at TS19453 and D1, the switching frequency is given as FS = (VIN - VOUT ) / (VIN * TOFF) When the TS19453 is powered from full wave rectified AC input, the swithching power loss can be estimated as: PSWITCH = 1 / (2 * TOFF) * ((VAC * CP + 2 * ISAT * trr ) * (VAC - VOUT ))) When the TS19453 is powered from DC input voltage, conduction power loss can be estimated as: PCOND = (D * IOUT 2 * R ON) + IDD * VIN * (1 – D) EMI Filter As with all off-line converters, selecting an input filter is critical to obtaining good EMI. A switching side capacitor, albeit of small value, is necessary in order to ensure low impedance to the high frequency switching currents of the converter. As a rule of thumb, this capacitor should be approximately 0.1~0.2µF/W of LED output power. |
Similar Part No. - TS19453CS-RLG |
|
Similar Description - TS19453CS-RLG |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |