Electronic Components Datasheet Search |
|
AT29LV040A-25TC Datasheet(PDF) 1 Page - ATMEL Corporation |
|
AT29LV040A-25TC Datasheet(HTML) 1 Page - ATMEL Corporation |
1 / 10 page 4 Megabit (512K x 8) 3-volt Only 256 Byte Sector CMOS Flash Memory Features • Single Voltage, Range 3V to 3.6V Supply • 3-Volt-Only Read and Write Operation • Software Protected Programming • Fast Read Access Time - 200 ns • Low Power Dissipation 15 mA Active Current 20 µA CMOS Standby Current • Sector Program Operation Single Cycle Reprogram (Erase and Program) 2048 Sectors (256 bytes/sector) Internal Address and Data Latches for 256-Bytes • Two 16 KB Boot Blocks with Lockout • Fast Sector Program Cycle Time - 20 ms Max. • Internal Program Control and Timer • DATA Polling for End of Program Detection • Typical Endurance > 10,000 Cycles • CMOS and TTL Compatible Inputs and Outputs • Commercial and Industrial Temperature Ranges Description The AT29LV040A is a 3-volt-only in-system Flash Programmable and Erasable Read Only Memory (PEROM). Its 4 megabits of memory is organized as 524,288 words by 8 bits. Manufactured with Atmel’s advanced nonvolatile CMOS EEPROM technology, the device offers access times up to 200 ns, and a low 54 mW power dissipation. When the device is deselected, the CMOS standby current is less than 20 µA. The device endurance is such that any sector can typically be written to in excess of 10,000 times. The programming algorithm is compatible with other devices in Atmel’s 3-volt-only Flash memories. To allow for simple in-system reprogrammability, the AT29LV040A does not require high input voltages for programming. Three-volt-only commands determine the opera- tion of the device. Reading data out of the device is similar to reading from an EPROM. Reprogramming the AT29LV040A is performed on a sector basis; 256-bytes of data are loaded into the device and then simultaneously programmed. During a reprogram cycle, the address locations and 256-bytes of data are captured at microprocessor speed and internally latched, freeing the address and data bus for other operations. Following the initiation of a program cycle, the device will automat- ically erase the sector and then program the latched data using an internal control timer. The end of a program cycle can be detected by DATA polling of I/O7. Once the end of a program cycle has been detected, a new access for a read or program can begin. AT29LV040A Pin Configurations Pin Name Function A0 - A18 Addresses CE Chip Enable OE Output Enable WE Write Enable I/O0 - I/O7 Data Inputs/Outputs NC No Connect TSOP Top View Type 1 0334C AT29LV040A 4-83 |
Similar Part No. - AT29LV040A-25TC |
|
Similar Description - AT29LV040A-25TC |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |