Electronic Components Datasheet Search |
|
ADSP-2185LKST-210 Datasheet(PDF) 7 Page - Analog Devices |
|
ADSP-2185LKST-210 Datasheet(HTML) 7 Page - Analog Devices |
7 / 48 page ADSP-2184L/ADSP-2185L/ADSP-2186L/ADSP-2187L Rev. C | Page 7 of 48 | January 2008 faster rate than can be serviced, due to the additional time the processor takes to come out of the idle state (a maximum of n processor cycles). SYSTEM INTERFACE Figure 2 shows typical basic system configurations with the ADSP-218xL series, two serial devices, a byte-wide EPROM, and optional external program and data overlay memories (mode-selectable). Programmable wait state generation allows the processor to connect easily to slow peripheral devices. ADSP-218xL series members also provide four external inter- rupts and two serial ports or six external interrupts and one serial port. Host Memory Mode allows access to the full external data bus, but limits addressing to a single address bit (A0). Through the use of external hardware, additional system peripherals can be added in this mode to generate and latch address signals. Clock Signals ADSP-218xL series members can be clocked by either a crystal or a TTL-compatible clock signal. The CLKIN input cannot be halted, changed during operation, nor operated below the specified frequency during normal oper- ation. The only exception is while the processor is in the power-down state. For additional information, refer to the ADSP-218x DSP Hardware Reference, for detailed information on this power-down feature. If an external clock is used, it should be a TTL-compatible signal running at half the instruction rate. The signal is connected to the processor’s CLKIN input. When an external clock is used, the XTAL pin must be left unconnected. ADSP-218xL series members use an input clock with a fre- quency equal to half the instruction rate; a 40 MHz input clock yields a 12.5 ns processor cycle (which is equivalent to 80 MHz). Normally, instructions are executed in a single pro- cessor cycle. All device timing is relative to the internal instruction clock rate, which is indicated by the CLKOUT signal when enabled. Because ADSP-218xL series members include an on-chip oscil- lator circuit, an external crystal may be used. The crystal should be connected across the CLKIN and XTAL pins, with two capacitors connected as shown in Figure 3. Capacitor values are dependent on crystal type and should be specified by the crystal manufacturer. A parallel-resonant, fundamental frequency, microprocessor-grade crystal should be used. To provide an adequate feedback path around the internal amplifier circuit, place a resistor in parallel with the circuit, as shown in Figure 3. A clock output (CLKOUT) signal is generated by the processor at the processor’s cycle rate. This can be enabled and disabled by the CLKODIS bit in the SPORT0 Autobuffer Control Register. Figure 2. Basic System Interface In ser t s yst em in ter fac e d iag ram he re 1/2 CLOCK OR CRYSTA L FL0–2 CLKIN XTAL SERIAL DEVICE SCLK1 RFS1 OR IRQ0 TFS1 OR IRQ1 DT1 OR FO DR1 OR FI SPORT1 SERIAL DEVICE A0–A21 DATA BYTE MEMORY I/O SPACE (PERIPHERALS) DATA ADDR DATA ADDR 2048 LOCATIONS OVERLAY MEMORY TWO 8K PM SEGMEN TS D23–0 A13–0 D23–8 A10–0 D15–8 D23–16 A13–0 14 24 SCLK0 RFS0 TFS0 DT0 DR0 SPORT0 DATA23–0 ADSP-218xL CS CS 1/2 CLOCK OR CRYSTAL CLK IN XTAL FL0–2 SERIAL DEVIC E SCLK1 RFS1 OR IRQ0 TFS1 OR IRQ1 DT1 OR FO DR1 OR FI SPORT1 16 IDMA PORT IRD/D6 IS/D4 IAL/D5 IACK/D3 IAD15-0 SERIAL DEVICE SC LK0 RFS0 TFS0 DT0 DR0 SPORT0 1 16 A0 DATA23–8 IOMS BMS DMS CMS BR BG BGH PWD PW DACK HOST MEMOR Y MODE FULL MEMORY MODE MODE D/PF3 MODE C/PF2 MODE B/PF1 MODE A/PF0 IRQ2/PF7 IRQE/PF4 IRQL0/PF5 MODE D/PF3 MODE C/PF2 MODE B/PF1 MODE A/PF0 WR RD SYSTEM INTERFAC E OR µC ONTRO LLER IRQ2/PF7 IRQE/PF4 IRQL0/PF5 IRQL1/PF6 IOMS BMS PMS CMS BR BG BGH PWD PW DACK WR RD AD SP-218xL DMS TW O 8K DM SEGMEN TS PMS ADDR13–0 IRQL1/PF6 IWR/D7 NOTE: MO D E D APPLIES TO THE AD SP-2187L P RO CES SOR ON LY |
Similar Part No. - ADSP-2185LKST-210 |
|
Similar Description - ADSP-2185LKST-210 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |