Product Specification

PE43602

Page 4 of 11

©2008-2009 Peregrine Semiconductor Corp. All rights reserved.

Document No. 70-0248-05

│ UltraCMOS™ RFIC Solutions

0

5

10

15

20

25

30

1.0E+03

1.0E+04

1.0E+05 1.0E+06 1.0E+07

1.0E+08 1.0E+09

Hz

Exposed

Solder

Pad

NC

VDD

P/S

GND

GND

LE

CLK

SI

RF1

18

17

16

15

14

13

2

3

4

5

6

1

RF2

GND

GND

Figure 13. Pin Configuration (Top View)

Table 2. Pin Descriptions

Pin No.

Pin Name

Description

1

GND

Ground

2

Power supply pin

3

P̅/S

Serial/Parallel mode select

4

GND

Ground

5

RF1

RF1 port

6 - 13

GND

Ground

14

RF2

RF2 port

15

GND

Ground

16

LE

Serial interface Latch Enable input

17

CLK

Serial interface Clock input

18

SI

Serial interface Data input

19

C16 (D6)

Parallel control bit, 16 dB

20

C8 (D5)

Parallel control bit, 8 dB

21

C4 (D4)

Parallel control bit, 4 dB

22

C2 (D3)

Parallel control bit, 2 dB

23

C1 (D2)

Parallel control bit, 1 dB

24

C0.5 (D1)

Parallel control bit, 0.5 dB

Paddle

GND

Ground for proper operation

Electrostatic Discharge (ESD) Precautions

When handling this UltraCMOS™ device, observe the

same precautions that you would use with other ESD-

sensitive devices. Although this device contains

circuitry to protect it from damage due to ESD,

precautions should be taken to avoid exceeding the

specified rating.

Exposed Solder Pad Connection

The exposed solder pad on the bottom of the package

must be grounded for proper device operation.

Latch-Up Avoidance

Unlike conventional CMOS devices, UltraCMOS™

devices are immune to latch-up.

Switching Frequency

The PE43602 has a maximum 25 kHz switching rate.

Switching rate is defined to be the speed at which the

DSA can be toggled across attenuation states.

Exceeding absolute maximum ratings may cause

permanent damage. Operation should be restricted to

the limits in the Operating Ranges table. Operation

between operating range maximum and absolute

maximum for extended periods may reduce reliability.

Moisture Sensitivity Level

The Moisture Sensitivity Level rating for the PE43602 in

the 24-lead 4x4 QFN package is MSL1.

Note: 1. Human Body Model (HBM, MIL_STD 883 Method 3015.7)

Figure 14. Maximum Power Handling Capability

Table 3. Operating Ranges

Table 4. Absolute Maximum Ratings

Symbol

Parameter/Conditions

Min

Max

Units

Power supply voltage

-0.3

6.0

V

Voltage on any Digital input

-0.3

5.8

V

Storage temperature range

-65

150

°C

Input power (50

Ω)

9 kHz

≤ 20 MHz

20 MHz

≤ 5 GHz

Fig. 14

+23

dBm

dBm

ESD voltage (Machine Model)

500

100

V

V

Parameter

Min

Typ

Max

Units

3.0

3.3

V

70

350

µA

Digital Input High

2.6

5.5

V

9 kHz

≤ 20 MHz

20 MHz

≤ 5 GHz

Fig. 14

+23

dBm

dBm

-40

25

85

°C

Digital Input Low

0

1

V

15

µA

5.0

5.5

V

Note 1. Input leakage current per Control pin

Note: Ground C0.5, C1, C2, C4, C8, C16 if not in use.