PE9701 datasheet(8/13 Pages) PSEMI

Part #	PE9701

Description	3000 MHz UltraCMOS Integer-N PLL Rad Hard for Space Applications

Download	13 Pages

Scroll/Zoom	100%

Manufacturer	PSEMI [Peregrine Semiconductor]

Direct Link	http://www.psemi.com

Logo

8 / 13 page

Product Specification

PE9701

Page 8 of 13

Document No. 70-0035-02

│ UltraCMOS™ RFIC Solutions

Main Counter Chain

Normal Operating Mode

The main counter chain divides the RF input

frequency, Fin, by an integer derived from the

user-defined values in the “M” and “A” counters. It

is composed of the 10/11 dual modulus prescaler,

modulus select logic, and 9-bit M counter. Setting

Pre_en “low” enables the 10/11 prescaler. Setting

Pre_en “high” allows F

in to bypass the prescaler

and powers down the prescaler.

The output from the main counter chain, fp, is

related to the VCO frequency, Fin, by the following

equation:

fp = Fin / [10 x (M + 1) + A]

(1)

where A

≤ M + 1, 1 ≤ M ≤ 511

When the loop is locked, Fin is related to the

reference frequency, fr, by the following equation:

Fin = [10 x (M + 1) + A] x (fr / (R+1))

(2)

where A

≤ M + 1, 1 ≤ M ≤ 511

A consequence of the upper limit on A is that Fin

must be greater than or equal to 90 x (fr / (R+1)) to

obtain contiguous channels. Programming the M

Counter with the minimum value of “1” will result in

a minimum M Counter divide ratio of “2”.

In Direct Interface Mode, main counter inputs M7

and M8 are internally forced low. In this mode, the

M value is limited to 1

≤ M ≤ 127.

Prescaler Bypass Mode

Setting

Pre_en “high” allows F

in to bypass and

power down the prescaler. In this mode, the

10/11 prescaler and A register are not active, and

the input VCO frequency is divided by the M

counter directly. The following equation relates Fin

to the reference frequency, fr:

Fin = (M + 1) x (fr / (R+1)) )

(3)

where 1 ≤ M ≤ 511

In Direct Interface Mode, main counter inputs M7

and M8 are internally forced low. In this mode, the

M value is limited to 1

≤ M ≤ 127.

Reference Counter

The reference counter chain divides the

reference frequency, fr, down to the phase

detector comparison frequency, fc.

The output frequency of the 6-bit R Counter is

related to the reference frequency by the

following equation:

fc = fr / (R + 1)

(4)

where 0 ≤ R ≤ 63

Note that programming R with “0” will pass the

reference frequency, fr, directly to the phase

detector.

In Direct Interface Mode, R Counter inputs R4

and R5 are internally forced low (“0”).

In this

mode, the R value is limited to 0

≤ R ≤ 15.

Register Programming

Parallel Interface Mode

Parallel Interface Mode is selected by setting the

Bmode input “low” and the Smode input “low”.

Parallel input data, D[7:0], is latched in a parallel

fashion into one of three 8-bit primary register

sections on the rising edge of M1_WR, M2_WR,

or A_WR per the mapping shown in Table 7 on

page 9. The contents of the primary register are

transferred into a secondary register on the

rising edge of Hop_WR according to the timing

diagram shown in Figure 5. Data is transferred

to the counters as shown in Table 7 on page 9.

The secondary register acts as a buffer to allow

rapid

changes to the VCO frequency.

This

double buffering for “ping-pong” counter control

is programmed via the FSELP input.

When

FSELP is “high”, the primary register contents

set the counter inputs. When FSELP is “low”,

the secondary register contents are utilized.

Parallel input data, D[7:0], is latched into the

enhancement register on the rising edge of

E_WR according to the timing diagram shown in

Figure 5. This data provides control bits as

shown in Table 8 on page 9 with bit functionality

enabled by asserting the

Enh input “low”

Similar Part No. - PE9701

Manufacturer	Part #	Datasheet	Description
Peregrine Semiconductor...	PE9701	280Kb / 13P	3000 MHz UltraCMOS??Integer-N PLL Rad Hard for Space Applications
Pasternack Enterprises,...	PE9701	77Kb / 1P	FME PLUG TO UHF MALE
Peregrine Semiconductor...	PE9701EK	280Kb / 13P	3000 MHz UltraCMOS??Integer-N PLL Rad Hard for Space Applications
Peregrine Semiconductor...	PE9701ES	280Kb / 13P	3000 MHz UltraCMOS??Integer-N PLL Rad Hard for Space Applications

More results

Similar Description - PE9701

Manufacturer	Part #	Datasheet	Description
Peregrine Semiconductor...	PE9704	246Kb / 10P	3000 MHz UltraCMOS??Integer-N PLL Rad Hard for Space Applications
Peregrine Semiconductor...	PE9702	260Kb / 13P	3000 MHz UltraCMOS??Integer-N PLL Rad Hard for Space Applications
Peregrine Semiconductor	PE9704	248Kb / 10P	3000 MHz UltraCMOS Integer-N PLL Rad Hard for Space Applications
Peregrine Semiconductor	PE9702	263Kb / 13P	3000 MHz UltraCMOS Integer-N PLL Rad Hard for Space Applications
Peregrine Semiconductor...	PE9701	280Kb / 13P	3000 MHz UltraCMOS??Integer-N PLL Rad Hard for Space Applications
Peregrine Semiconductor...	PE97022	355Kb / 14P	3500 MHz UltraCMOS Integer-N PLL Rad Hard for Space Applications
Peregrine Semiconductor	PE97042	461Kb / 11P	3.5 GHz UltraCMOS Integer-N PLL Rad Hard for Space Applications
	PE97022	561Kb / 14P	3.5 GHz UltraCMOS Integer-N PLL Rad Hard for Space Applications
	PE9601	490Kb / 14P	2200 MHz UltraCMOS Integer-N PLL for Rad Hard Applications
Peregrine Semiconductor...	PE9601	258Kb / 14P	2200 MHz UltraCMOS??Integer-N PLL for Rad Hard Applications

More results

PE9701 Datasheet(PDF) 8 Page - Peregrine Semiconductor

PE9701 Datasheet(HTML) 8 Page - Peregrine Semiconductor

Similar Part No. - PE9701

Similar Description - PE9701

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13

Datasheet Download

Link URL