■Dimensions

A5

B6

C6

E7

F8

E12

F12

φD±0.5

4.0

5.0

6.3

8.0

10.0

8.0

10.0

W

±0.2

5.4

5.9

5.9

6.9

7.9

11.9

12.6

4.3

5.3

6.6

8.3

10.3

8.3

10.3

H

±0.2

4.3

5.3

6.6

8.3

10.3

8.3

10.3

C

±0.2

5.0

6.0

7.3

9.0

11.0

9.0

11.0

R

0.6 to 0.8

0.6 to 0.8

0.6 to 0.8

0.6 to 0.8

0.6 to 0.8

0.8 to 1.1

0.8 to 1.1

P

±0.2

1.0

1.4

2.1

3.2

4.6

3.2

4.6

Size Code

(unit : mm)

■Size List

30

3.3

4.7

6.8

10

15

22

27

33

39

47

56

68

82

100

120

150

180

220

270

330

470

560

680

820

1200

1500

C6

E12

F12

RV

（SV）

µF

2.5

（3.3）

4

（5.2）

6.3

（8.2）

10

（11.5）

16

（18.4）

20

（23.0）

25

（25.0）

A5

B6

B6

C6,E7

E7

E12

F8

F12

A5

B6

C6

C6

C6

E7,F8

F8

F8,E12

F12

A5

A5

A5

A5

B6

C6

C6

E7

E7,F8

F8

F8,E12

F12

A5

B6

B6

C6

E7

E7

F8

F8

F8,E12

F12

B6

C6

C6

E7

E7

F8

F8

E12

F12

C6

E7

F8

E12

F12

RV : Rated voltage

(SV) : Surge (room temperature)

※For the minimum packing quantity, please refer to page 55.

Standard SMD type product

Use for surface mounted type switching power supplies.

This product can support lead free-reflow. (

※2).

Marking : Polarity( ), Rated voltage, Lot.No.

(Purple) SVP(Upper E7), Rated capacitance.

■Specifications

※1 In case of some problems for measured values, measure after applying rated voltage for 2.5 to 20V products or 20V for 25V products

   for 120 minutes at 105

°C .

※2 Refer to Page 56 for reflow soldering conditions.

4. SPECIFICATIONS FOR EACH SERIES

L

R

W

0.2max.

（＋）

■Recommended land pattern

dimension of PWB

a

b

Size Code

A5

B6

C6

E7

F8

E12

F12

ab

c

1.0

1.4

2.1

2.8

4.3

2.8

4.3

6.2

7.4

9.1

11.1

13.1

11.1

13.1

1.6

1.6

1.6

1.9

1.9

1.9

1.9

(unit : mm)

Conductive polymer type

Standard SMD type

L

+0.1

-0.4

Items

Characteristics

-55

°C to +105°C

M:

±20%

Less than or equal to the value of Table7

Less than or equal to the value of Table7

Less than or equal to the value of Table7

Within

±20%

1.5 times or less than an initial standard

1.5 times or less than an initial standard

Below an initial standard

Within

±20%

1.5 times or less than an initial standard

1.5 times or less than an initial standard

Below an initial standard (after voltage processing)

Within

±10%

1.3 times or less than an initial standard

1.3 times or less than an initial standard

Below an initial standard (after voltage processing)

Category temperature range

Tolerance on rated capacitance

Tangent of loss angle

Leakage current

ESR

Endurance

Damp heat (Steady state)

Characteristics of impedance

ratio at high temp. and low temp.

-55

°C

+105

°C

∆C/C

tan

δ

ESR

Leakage current

∆C/C

tan

δ

ESR

Leakage current

∆C/C

tan

δ

ESR

Leakage current

Resistance to

soldering heat

0.75 to 1.25

0.75 to 1.25

120Hz

120Hz

105

°C, 2,000h, Rated

voltage applied

(25V

→20V applied)

60

°C, 90 to 95%RH,

1,000h,

No-applied voltage

(VPS) (230

°C X 75s)

※1

※2

Conditions

Based the value at

100KHz

，+20

°C

After 2 minutes