MBRM140 datasheet(11/20 Pages) LINER

Part #	MBRM140

Description	True Color PWM Delivers Constant Color with 400:1 Dimming Range

Download	20 Pages

Scroll/Zoom	100%

Manufacturer	LINER [Linear Technology]

Direct Link	http://www.linear.com

Logo

11 / 20 page

LT3474/LT3474-1

11

3474fd

APPLICATIONS INFORMATION

The optimum inductor for a given application may differ

from the one indicated by this simple design guide. A

larger value inductor provides a higher maximum load

current, and reduces the output voltage ripple. If your

load is lower than the maximum load current, then you

can relax the value of the inductor and operate with higher

ripple current. This allows you to use a physically smaller

inductor, or one with a lower DCR resulting in higher

efﬁciency. Be aware that if the inductance differs from

the simple rule above, then the maximum load current

will depend on input voltage. In addition, low inductance

may result in discontinuous mode operation, which further

reduces maximum load current. For details of maximum

output current and discontinuous mode operation, see

Linear Technology’s Application Note 44. Finally, for duty

cycles greater than 50% (VOUT/VIN > 0.5), a minimum

inductance is required to avoid sub-harmonic oscillations.

See Application Note 19.

The current in the inductor is a triangle wave with an average

value equal to the load current. The peak switch current

is equal to the output current plus half the peak-to-peak

inductor ripple current. The LT3474 limits its switch cur-

rent in order to protect itself and the system from overload

faults. Therefore, the maximum output current that the

LT3474 will deliver depends on the switch current limit,

the inductor value, and the input and output voltages.

When the switch is off, the potential across the inductor

is the output voltage plus the catch diode drop. This gives

the peak-to-peak ripple current in the inductor

ΔIL =

1– DC

() VOUT + VF

()

L•f

()

where f is the switching frequency of the LT3474 and L

is the value of the inductor. The peak inductor and switch

current is

I

SW PK

() =

I

LPK

() =

I

OUT +

ΔIL

2

Inductor Selection and Maximum Output Current

A good first choice for the inductor value is

LV

V

kHz

f

OUT

F

=+

•

()

900

where VF is the voltage drop of the catch diode (~0.4V), f

is the switching frequency and L is in μH. With this value

the maximum load current will be 1.1A, independent of

input voltage. The inductor’s RMS current rating must be

greater than the maximum load current and its saturation

current should be at least 30% higher. For highest efﬁciency,

the series resistance (DCR) should be less than 0.2Ω.

Table 2 lists several vendors and types that are suitable.

For robust operation at full load and high input voltages

(VIN > 30V), use an inductor with a saturation current

higher than 2.5A.

Table 2. Inductors

PART NUMBER

VALUE

(μH)

IRMS

(A)

DCR

(Ω)

HEIGHT

(mm)

Sumida

CR43-3R3

3.3

1.44

0.086

3.5

CR43-4R7

4.7

1.15

0.109

3.5

CDRH4D16-3R3

3.3

1.1

0.063

1.8

CDRH4D28-3R3

3.3

1.57

0.049

3

CDRH4D28-4R7

4.7

1.32

0.072

3

CDRH5D28-100

10

1.3

0.048

3

CDRH5D28-150

15

1.1

0.076

3

CDRH73-100

10

1.68

0.072

3.4

CDRH73-150

15

1.33

0.13

3.4

Coilcraft

DO1606T-332

3.3

1.3

0.1

2

DO1606T-472

4.7

1.1

0.12

2

DO1608C-332

3.3

2

0.08

2.9

DO1608C-472

4.7

1.5

0.09

2.9

MOS6020-332

3.3

1.8

0.046

2

MOS6020-472

10

1.5

0.05

2

Similar Part No. - MBRM140

Manufacturer	Part #	Datasheet	Description
ON Semiconductor	MBRM140	94Kb / 8P	Surface Mount Schottky Power Rectifier December, 2002 - Rev. 1
	MBRM140	69Kb / 5P	Surface Mount Schottky Power Rectifier September, 2006 ??Rev. 3
	MBRM140D	94Kb / 8P	Surface Mount Schottky Power Rectifier December, 2002 - Rev. 1
	MBRM140E	158Kb / 5P	Low Leakage Surface Mount Schottky Power Rectifier September, 2006 ??Rev. 2
	MBRM140ET1	158Kb / 5P	Low Leakage Surface Mount Schottky Power Rectifier September, 2006 ??Rev. 2

More results

Similar Description - MBRM140

Manufacturer	Part #	Datasheet	Description
Linear Technology	LT3478-1	293Kb / 24P	4.5A Monolithic LED Drivers with True Color PWM Dimming
	LT3478	293Kb / 24P	4.5A Monolithic LED Drivers with True Color PWM Dimming
	LT3478	288Kb / 24P	4.5A Monolithic LED Drivers with True Color PWM Dimming
ON Semiconductor	CAT4101TV-T75	158Kb / 11P	1 A Constant-Current LED Driver with PWM Dimming Doc. No. MD-5036, Rev. D
SHENZHEN FUMAN ELECTRON...	FM7609	258Kb / 7P	Non-isolated step-down PWM dimming color temperature LED constant current driver IC
ON Semiconductor	CAT4101	159Kb / 10P	1 A Constant-Current LED Driver with PWM Dimming February, 2010 ??Rev. 4
SHENZHEN FUMAN ELECTRON...	TC3085CL	738Kb / 8P	Switch dimming / color linear LED constant current driver chip
List of Unclassifed Man...	3200124	51Kb / 3P	Ferrules with plastic sleeve, color range 1
E-CMOS Corporation	EC4215	257Kb / 6P	Constant Current LED Driver with PWM Dimming
Shenzhen Huazhimei Semi...	HM7169	1Mb / 15P	Segment dimming/color adjustment LED linear constant current control chip

More results

MBRM140 Datasheet(PDF) 11 Page - Linear Technology

MBRM140 Datasheet(HTML) 11 Page - Linear Technology

Similar Part No. - MBRM140

Similar Description - MBRM140

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Datasheet Download

Link URL