Electronic Components Datasheet Search |
|
OPA2343UA Datasheet(PDF) 8 Page - Texas Instruments |
|
|
OPA2343UA Datasheet(HTML) 8 Page - Texas Instruments |
8 / 16 page OPA343, 2343, 4343 8 SBOS090A APPLICATIONS INFORMATION OPA343 series op amps are fabricated on a state-of-the-art 0.6 micron CMOS process. They are unity-gain stable and suitable for a wide range of general-purpose applications. Rail-to-rail input/output make them ideal for driving sam- pling A/D converters. In addition, excellent ac performance makes them well-suited for audio applications. The class AB output stage is capable of driving 600 Ω loads connected to any point between V+ and ground. Rail-to-rail input and output swing significantly increases dynamic range, especially in low-supply applications. Fig- ure 1 shows the input and output waveforms for the OPA343 in unity-gain configuration. Operation is from a single +5V supply with a 10k Ω load connected to V S /2. The input is a 5Vp-p sinusoid. Output voltage is approxi- mately 4.98Vp-p. Power-supply pins should be bypassed with 0.01 µF ceramic capacitors. OPERATING VOLTAGE OPA343 series op amps are fully specified from +2.7V to +5V. However, supply voltage may range from +2.5V to +5.5V. Parameters are guaranteed over the specified supply range—a unique feature of the OPA343 series. In addition, many specifications apply from –40 °C to +85°C. Most behavior remains virtually unchanged throughout the full operating voltage range. Parameters which vary signifi- cantly with operating voltages or temperature are shown in the Typical Performance Curves. RAIL-TO-RAIL INPUT The input common-mode voltage range of the OPA343 series extends 500mV beyond the supply rails. This is achieved with a complementary input stage—an N-channel input differential pair in parallel with a P-channel differen- tial pair, as shown in Figure 2. The N-channel pair is active for input voltages close to the positive rail, typically (V+) – 1.3V to 500mV above the positive supply. The P-channel pair is on for inputs from 500mV below the negative supply to approximately (V+) – 1.3V. There is a small transition region, typically (V+) – 1.5V to (V+) – 1.1V, in which both input pairs are on. This 400mV transition region can vary ±300mV with process variation. Thus, the transition region (both stages on) can range from (V+) – 1.8V to (V+) – 1.4V on the low end, up to (V+) – 1.2V to (V+) – 0.8V on the high end. Within the 400mV transition region PSRR, CMRR, offset voltage, offset drift, and THD may be degraded compared to operation outside this region. A double-folded cascode adds the signal from the two input pairs and presents a differential signal to the class AB output stage. Normally, input bias current is approximately 200fA, however, input voltages exceeding the power supplies by FIGURE 2. Simplified Schematic. V S = +5, G = +1, RL = 10kΩ 5 5 0 V IN V OUT FIGURE 1. Rail-to-Rail Input and Output. V BIAS1 V BIAS2 V IN+ V IN– Class AB Control Circuitry V O V– (Ground) V+ Reference Current |
Similar Part No. - OPA2343UA |
|
Similar Description - OPA2343UA |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |