3M

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

.100

″ × .100″ Latch/Ejector, Straight and Right Angle

3000 Series

Table 1

Pin

Quantity

3M Part

Number

Dimensions

Polarization

Notches Provided

A

B

C

D

10

3793

1.26 [32.1]

1.105 [28.07]

.865 [21.97]

.71 [18.0]

B C

14

3314

1.46 [37.2]

1.305 [33.15]

1.065 [27.05]

.91 [23.1]

B C

16

3408

1.56 [39.7]

1.405 [35.69]

1.165 [29.59]

1.01 [25.6]

A B C

20

3428

1.76 [44.8]

1.605 [40.77]

1.365 [34.67]

1.21 [30.7]

A B C

24

3627

1.96 [49.8]

1.805 [45.85]

1.565 [39.75]

1.41 [35.8]

A B C

26

3429

2.06 [52.4]

1.905 [48.39]

1.665 [42.29]

1.51 [38.3]

A B C

30

3440

2.26 [57.4]

2.105 [53.47]

1.865 [47.37]

1.71 43.43]

A B C

34

3431

2.46 [62.6]

2.305 [58.55]

2.065 [52.45]

1.91 [48.5]

A B C

40

3432

2.76 [70.2]

2.605 [66.17]

2.365 [60.07]

2.21 [56.1]

A B C

50

3433

3.26 [82.9]

3.105 [78.87]

2.865 [72.77]

2.71 [68.8]

A B C

60

3372

3.76 [95.6]

3.605 [91.57]

3.365 [85.47]

3.21 [81.5]

A B C

64

3764

3.96 [100.7]

3.805 [96.65]

3.565 [90.55]

3.41 [86.6]

A B C

TS-0772-04

Sheet 3 of 4

Inch

± .005

± .1

± .01

Tolerance Unless Noted

.0

.00

.000

Inch

[ ] Dimensions for

Reference only

[mm]

ø.106

[2.69]

or

ø.116

[2.95]

(See Note 2)

Dia

Position 1

.100

± .003

[2.54]

.100

± .003

[2.54]

.060

[1.52]

.300

[7.62]

Side to Side Stackability

B

Recommended Mounting Hole Pattern

(Straight)

.352

[8.94]

CL

“Y”

.035

[0.89]

CL

"Y"

.41

[10.4]

Max to Edge of PCB

for Daisy Chain

ø.106

[2.69]

or ø.116

[2.95]

(See Note 2)

.035

[0.89]

Dia

.029

[0.74]

.100

± .003

[2.54]

Position 1

.232

[5.89]

C

Recommended Mounting Hole Pattern

(Right Angle)

.100

± .003

[2.54]

Ordering Information

NXXXX-XX02RB

3M Part Number

(See Table 1)

Pin Configuration

5 = Right Angle

6 = Straight

Latch/Ejector System

2 = Short Roll Pin Latch/Ejectors

(3M Part # N3505-2)

3 = Long Roll Pin Latch/Ejectors

(3M Part # N3505-3)

Notes:

1. Notches A & C will accomodate 3M Polarizing Keys (3M Part #N3518).

2. Mounting hardware: From solder side of pc board use #4-24 thread cutting screw (3M Part # 3341-5) and .116 [2.95]

dia mounting hole. For right angle version only, #2-56 bolt and nut (3M Part # 3341-6) with .106 [2.69] dia mounting hole

may be used.

3. .112 [2.84] tail length suitable for .062 [1.57] thick pc board.

4. Contact tails .0245 [0.622] crowned wire with .0075 [0.191] corner radii & .028 [.072] diagonal.

5. Contact your 3M sales representative for custom requirements.