Electronic Components Datasheet Search |
|
GRM1555C1H100JA01D Datasheet(PDF) 2 Page - Murata Manufacturing Co., Ltd. |
|
GRM1555C1H100JA01D Datasheet(HTML) 2 Page - Murata Manufacturing Co., Ltd. |
2 / 29 page Temperature Compensating Type High Dielectric Constant Type 1 Operating -55℃ to 125℃ R6:-55℃ to 85℃ Reference Temperature : 25℃ Temperature Range R7:-55℃ to 125℃ C8:-55℃ to 105℃ E4:10℃ to 85℃ F5:-30℃ to 85℃ L8/R9:-55℃ to 150℃ 2 Rated Voltage See the previous pages. The rated voltage is defined as the maximum voltage which may be applied continuously to the capacitor. When AC voltage is superimposed on DC voltage, V P-P or VO-P, whichever is larger, should be maintained within the rated voltage range. 3 Appearance No defects or abnormalities. Visual inspection. 4 Dimension Within the specified dimensions. Using calipers. (GRM02 size is based on Microscope) 5 Dielectric Strength No defects or abnormalities. No failure should be observed when 300% of the rated voltage (ΔC to7U and 1X) or 250% of the rated voltage (R6,R7,C8,E4,F5,L8 and R9) is applied between the terminations for 1 to 5 seconds, provided the charge/discharge current is less than 50mA. 6 Insulation More than 10,000M Ω or 500Ω ∙F The insulation resistance should be measured with a DC voltage Resistance (whichever is smaller) not exceeding the rated voltage at 25℃ and 75%RH max. and within 2 minutes of charging, provided the charge/discharge current is less than 50mA. 7 Capacitance Within the specified tolerance. The capacitance/Q/D.F. should be measured at 25℃ at the frequency and voltage shown in the table. 8 Q/Dissipation 30pF and over:Q≧1000 [R6,R7,C8,L8] (1)Temperature Compensating Type Factor (D.F.) 30pF and below:Q≧400+20C W.V.:100V :0.025max.(C<0.068 mF) :0.05max.(C≧0.068 mF) C:Nominal Capacitance(pF) W.V.:50V/25V :0.025max. W.V.:16V/10V :0.035max. W.V.:6.3V/4V :0.05max.(C<3.3 mF) :0.1max.(C≧3.3 mF) (2)High Dielectric Constant Type [R9] W.V.:50V: 0.05max. [E4] W.V.:25Vmin: 0.025max. [F5] W.V.:25Vmin :0.05max. (C<0.1 mF) :0.09max.(C≧0.1 mF) W.V.:16V/10V:0.125max. W.V.:6.3V:0.15max. 9 Capacitance Capacitance Within the specified The capacitance change should be measured after 5min. at each Temperature Change tolerance.(Table A-1) specified temp.stage. Characteristics (1)Temperature Compensating Type The temperature coefficient is determind using the capacitance measured in step 3 as a reference. When cycling the temperature sequentially from step 1 through 5 ( Δ C:+25℃ to +125℃,other temp.coeffs.:+25℃ to +85℃) the capacitance should be within the specified tolerance for the temperature coefficient and capacitance change as Table A-1. The capacitance drift is caluculated by dividing the differences between the maximum and minimum measured values in the step 1,3 and 5 by the cap.value in step 3. Temperature Within the specified Coefficent tolerance.(Table A-1) Capacitance Within±0.2% or±0.05pF Drift (Whichever is larger.) *Not apply to 1X/25V (2)High Dielectric Constant Type The ranges of capacitance change compared with the 25℃ value over the temperature ranges shown in the table should be within the specified ranges.* Initial measurement for high dielectric constant type Perform a heat treatment at 150 +0/-10°C for one hour and then set for 24±2 hours at room temperature. Perform the initial measure-ment. 10 Adhesive Strength No removal of the terminations or other defect should occur. Solder the capacitor on the test jig (glass epoxy board)shown in of Termination Fig.3 using a eutectic solder. Then apply 10N* force in parallel with the test jig for 10±1sec. The soldering should be done either with an iron or using the reflow method and should be conducted with care so that the soldering is uniform and free of defects such as heat shock. *1N(GRM02),2N(GR□03),5N(GR□15,GRM18) ■SPECIFICATIONS AND TEST METHODS No Item Specification Test Method Step Temperature( C) 1 25±2 2 -55±3(for C to 7U/1X) 3 25±2 4 125±3(for Δ C), 85±3(for other TC) 5 25±2 Capacitance Frequency Voltage C≦ 10μF 1±0.1kHz 1±0.2Vrms C> 10μF 120±24Hz 0.5±0.1Vrms E4 1±0.1kHz 0.5±0.05Vrms Capacitance Frequency Voltage C≦1000pF 1±0.1MHz 0.5 to 5Vrms C>1000pF 1±0.1kHz 1±0.2Vrms Char. Temp. Range Reference Temp . Cap. Change R6 -55 C to +85C 25 C Within ±15% R7 -55 C to +125C Within ±15% C8 -55 C to +105C Within ±22% L8 -55 C to +125C Within ±15% +125 C to+150C Within+15/-40% R9 -55 C to+150C Within ±15% E4 +10 C to +85C Within+22/-56% F5 -30 C to +85C Within+22/-82% Step Temperature( C) 1 25±2 2 -55±3(for R6/R7/C8/L8/R9) -30±3(for F5) 10±3(for E4) 3 25±2 4 150±3(for L8/R9) 125±3(for R7) 105±3(for C8) 5 25±2 JEMCGS-0015Q 2 |
Similar Part No. - GRM1555C1H100JA01D |
|
Similar Description - GRM1555C1H100JA01D |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |