 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
ACT4808LDF Datasheet(PDF) 1 Page - Aeroflex Circuit Technology |
|
||||||||||||||||||||||||||||||
ACT4808LDF Datasheet(HTML) 1 Page - Aeroflex Circuit Technology |
|
|
1 / 8 page  eroflex Circuit T echnology – Data Bus Modules For The Future © SCD4808 REV E 12/9/99 CIRCUIT TECHNOLOGY www.aeroflex.com/act1.htm Features • ACT4808 Dual Transceiver meets MIL-STD-1553A& B, Macair A3818, A5690, A5232 and A4905 specs • New Low Power Model –L Available • Operates with ±12V to ±15V & +5V Power Supplies • Voltage source output for higher bus drive power • Plug-in or Flat Package • Monolithic construction using linear ASICs • Processed and Screened to MIL-STD-883 specs General Description: The Aeroflex Laboratories transceiver model ACT4808 is a new generation Dual monolithic transceiver which provides full compliance with Macair and MIL-STD-1553 data bus requirements The model ACT4808 performs the front-end analog function of inputting and outputting data through a transformer to a MIL-STD-1553 or Macair data bus. The ACT4808 can be considered a "Universal" Transceiver in that it is compatible with MIL-STD-1553A & B, Macair A-3818, A-4905, A-5232 and A-5690. Design of this transceiver reflects particular attention to active filter performance. This results in low bit and word error rate with superior waveform purity and minimal zero crossover distortion. The ACT4808 series active filter design has additional high frequency roll-off to provide the required Macair low harmonic distortion waveform without increasing the pulse delay characteristics significantly. Efficient transmitter electrical and thermal design provides low internal power dissipation and heat rise at high and well as low duty cycles.The receiver input threshold is set Internally. Transmitter The Transmitter section accepts bi-phase TTL data at the input and when coupled to the data bus as per Figure 3 or 4 and by two 70 Ohm terminations (ZO), the data bus signal produced is 6.5 Volts minimum P-P at A-A’. When both DATA and DATA ACT4808 Transceiver Block Diagram (without Transformer), 1/2 of unit shown SHAPING OUTPUT STAGE COMP. COMP. ACTIVE FILTER INPUT AMP DRIVER TX DATA IN TX DATA IN TX INHIBIT +5 V RX DATA IN RX DATA IN STROBE TX DATA OUT TX DATA OUT RX DATA OUT RX DATA OUT VEE VCC V+ V- ACT4808 Dual Transceivers for MACAIR A3818, A5690, A5232, A4905 & MIL-STD-1553 |
Similar Part No. - ACT4808LDF |
|
Similar Description - ACT4808LDF |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
