FOD8318 datasheet(6/31 Pages) FAIRCHILD

Part #	FOD8318

Description	2.5 A Output Current, IGBT Drive Optocoupler with Active Miller Clamp, Desaturation Detection, and Isolated Fault Sensing

Download	31 Pages

Scroll/Zoom	100%

Manufacturer	FAIRCHILD [Fairchild Semiconductor]

Direct Link	http://www.fairchildsemi.com

Logo

6 / 31 page

www.fairchildsemi.com

FOD8318 Rev. 1.1.2

6

Recommended Operating Conditions

The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended

operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not

recommend exceeding them or designing to absolute maximum ratings.

Note:

6. During power up or down, it is important to ensure that VIN+ remains LOW until both the input and output supply

voltages reach the proper recommended operating voltage to avoid any momentary instability at the output state.

Refer to “Time to Good Power” section on page 25.

Isolation Characteristics

Apply over all recommended conditions, typical value is measured at TA = 25 ºC

Notes:

7. Device is considered a two terminal device: pins 1 to 8 are shorted together and pins 9 to 16 are shorted together.

8. 4,243 VRMS for 1-minute duration is equivalent to 5,091 VRMS for 1-second duration.

9. The Input-Output Isolation Voltage is a dielectric voltage rating as per UL1577. It should not be regarded as an

input-output continuous voltage rating. For the continuous working voltage rating, refer to the equipment level safety

specification or DIN EN/IEC 60747-5-5 Safety and Insulation Ratings Table on page 4.

Electrical Characteristics

Apply over all recommended conditions; typical value is measured at VDD1 = 5 V, VDD2 – VSS = 30 V, VE – VSS = 0 V,

TA = 25 °C unless otherwise specified.

Symbol

Parameter

Min.

Max.

Unit

TA

Ambient Operating Temperature

-40

+100

ºC

VDD1

Input Supply Voltage(6)

35.5

V

VDD2 – VSS

Total Output Supply Voltage

15

30

V

VE – VSS

Negative Output Supply Voltage

0

15

V

VDD2 – VE

Positive Output Supply Voltage(6)

15

30 – (VE – VSS)V

VS

Source of Pull-up PMOS Transistor Voltage

VSS + 7.5

VDD2

V

Symbol

Parameter

Conditions

Min.

Typ.

Max.

Units

VISO

Input-Output Isolation

Voltage

TA = 25 ºC, R.H.< 50 %, t = 1.0 min,

II-O ð 10 µA, 50 Hz

(7)(8)(9)

4,243

VRMS

RISO

Isolation Resistance

VI-O = 500 V

(7)

1011

¾

CISO

Isolation Capacitance

VI-O = 0 V, freq = 1.0 MHz

(7)

1pF

Symbol

Parameter

Conditions

Min.

Typ.

Max.

Units Figure

VIN+L, VIN-L,

VRESETL

Logic Low Input Voltages

0.8

V

VIN+H,VIN-H,

VRESETH

Logic High Input Voltages

2.0

V

IIN+L, IIN-L,

IRESETL

Logic Low Input Currents

VIN = 0.4 V

-0.5

-0.001

mA

IFAULTL

FAULT Logic Low Output

Current

VFAULT = 0.4 V

5.0

12.0

mA

1, 35

IFAULTH

FAULT Logic High Output

Current

VFAULT = VDD1

-40

0.002

µA

35

IOH

High Level Output Current

VO = VDD2 – 3 V

-1

-3

A

2, 7, 36

VO = VDD2 – 6 V

(10)

-2.5

A

Similar Part No. - FOD8318

Manufacturer	Part #	Datasheet	Description
ON Semiconductor	FOD8318	497Kb / 30P	2.5 A Output Current, IGBT Drive Optocoupler with Active Miller Clamp, Desaturation Detection, and Isolated Fault Sensing October 2017 Rev. 2
	FOD8318	555Kb / 29P	2.5 A Output Current, IGBT Drive Optocoupler with Active Miller Clamp, Desaturation Detection, and Isolated Fault Sensing January, 2023 - Rev. 4
	FOD8318R2	497Kb / 30P	2.5 A Output Current, IGBT Drive Optocoupler with Active Miller Clamp, Desaturation Detection, and Isolated Fault Sensing October 2017 Rev. 2
	FOD8318R2	555Kb / 29P	2.5 A Output Current, IGBT Drive Optocoupler with Active Miller Clamp, Desaturation Detection, and Isolated Fault Sensing January, 2023 - Rev. 4
	FOD8318R2V	497Kb / 30P	2.5 A Output Current, IGBT Drive Optocoupler with Active Miller Clamp, Desaturation Detection, and Isolated Fault Sensing October 2017 Rev. 2

More results

Similar Description - FOD8318

Manufacturer	Part #	Datasheet	Description
ON Semiconductor	FOD8318	497Kb / 30P	2.5 A Output Current, IGBT Drive Optocoupler with Active Miller Clamp, Desaturation Detection, and Isolated Fault Sensing October 2017 Rev. 2
	FOD8318	555Kb / 29P	2.5 A Output Current, IGBT Drive Optocoupler with Active Miller Clamp, Desaturation Detection, and Isolated Fault Sensing January, 2023 - Rev. 4
	FOD8316	450Kb / 29P	2.5 A Output Current, IGBT Drive Optocoupler with Desaturation Detection and Isolated Fault Sensing October 2017 Rev. 2
	FOD8316	463Kb / 28P	2.5 A Output Current, IGBT Drive Optocoupler with Desaturation Detection and Isolated Fault Sensing February, 2023 - Rev. 3
AVAGO TECHNOLOGIES LIMI...	ACPL-332J-000E	299Kb / 23P	2.5 Amp Output Current IGBT Gate Driver Optocoupler with Integrated (VCE) Desaturation Detection, UVLO Fault Status Feedback and Active Miller Clamping
AVAGO TECHNOLOGIES LIMI...	ACPL-331J-500E	300Kb / 22P	1.5 Amp Output Current IGBT Gate Driver Optocoupler with Integrated (VCE) Desaturation Detection, UVLO, Fault Status Feedback and Active Miller Clamping
Broadcom Corporation.	ACPL-5160	2Mb / 36P	2.5-Amp Gate Drive Optocoupler with Integrated (VCE) Desaturation Detection and Fault Status Feedback
AVAGO TECHNOLOGIES LIMI...	ACPL-5160	557Kb / 33P	2.5 Amp Gate Drive Optocoupler with Integrated (VCE) Desaturation Detection and Fault Status Feedback
	HCPL-316J-500E	332Kb / 33P	2.5 Amp Gate Drive Optocoupler with Integrated (VCE) Desaturation Detection and Fault Status Feedback
	HCPL-316J-000E	332Kb / 33P	2.5 Amp Gate Drive Optocoupler with Integrated (VCE) Desaturation Detection and Fault Status Feedback

More results

FOD8318 Datasheet(PDF) 6 Page - Fairchild Semiconductor

FOD8318 Datasheet(HTML) 6 Page - Fairchild Semiconductor

Similar Part No. - FOD8318

Similar Description - FOD8318

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

Datasheet Download

Link URL