Electronic Components Datasheet Search |
|
RC0603FR-071KL Datasheet(PDF) 2 Page - Texas Instruments |
|
RC0603FR-071KL Datasheet(HTML) 2 Page - Texas Instruments |
2 / 12 page Operation www.ti.com 1.2 TPA2025D1 Specifications V BAT Supply voltage range 2.5 V to 5.2 V I DD Supply current 3 A Maximum P O Continuous output power per channel, 4 Ω, V BAT = 3.6 V 2 W V I Audio input voltage 0 V to V BAT R L Minimum load impedance 4 Ω 2 Operation This section describes how to operate the TPA2025D1EVM. 2.1 Quick-Start List for Stand-Alone Operation Use the following steps when operating the TPA2025D1EVM as a stand-alone or when connecting the EVM into existing circuits or equipment. 2.1.1 Power and Ground 1. Ensure the external power sources are set to OFF. 2. Set the power supply voltage between 2.3 V and 5.2 V. When connecting the power supply to the EVM, attach the power supply ground connection to the GND connector first, and then connect the positive supply to the VDD connector. Verify that correct connections are made to the banana jacks. 2.1.2 Audio 1. Ensure that the audio source is set to the minimum level. 2. Connect the audio source to the input RCA jack IN. In case of differential audio input, ensure that the jumper, JP SE, is not inserted. In case of a single-ended audio input, ensure that the jumper, JP SE, is inserted, thereby grounding IN+ through the input capacitor C2. 3. Connect a speaker (4 Ω to 32 Ω) to the output banana jacks, OUT+ and OUT–. 4. FLT Out+ and FLT OUT- test points allow the user to connect the outputs of the amplfier through an RC filter for audio measurements. (Many audio analyzers will not give the correct readings on a Class-D amplifier without additional filtering.) Note that the user must provide the necessary resistors, R7 and R8 to complete the filters. The typical value for R7 and R8 is 1.0 k Ω. 5. The filtered output of the TPA2025D1 can be measured between test points FILT OUT – and FILT OUT+ 2.1.3 AGC Control The TPA2025D1 has three selectable inflection point settings: 3.25 V, 3.55 V, and 3.75 V. 1. Remove the jumper, AGC, to select the 3.25-V inflection point (AGC1). 2. Install the jumper, AGC, between pins 2 and 3 to select the 3.55-V inflection point (AGC2). 3. Install the jumper, AGC, between pins 1 and 2 to select the 3.75-V inflection point (AGC3). 2.1.4 Amplifier Gain The TPA2025D1 has a fixed setting of 20 dB. 2.1.5 Shutdown Controls 1. The TPA2025D1 provides shutdown control for the Class-D amplifier and the boost converter. The EN pin enables the boost converter and Class-D amplifier. It is active high. 2. Press and hold pushbutton S1 to place the boost converter and the Class-D amplifier in shutdown. Release pushbutton S1 to activate the Class-D amplifier and boost converter. The boost converter only turns on if an audio signal ( > 2 V PEAK) is present at one of the outputs (OUT+ or OUT-). 2 TPA2025D1 Audio Power Amplifier Evaluation Module SLOU310 – September 2011 Submit Documentation Feedback Copyright © 2011, Texas Instruments Incorporated |
Similar Part No. - RC0603FR-071KL |
|
Similar Description - RC0603FR-071KL |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |