Electronic Components Datasheet Search |
|
bq27425YZFR-G1 Datasheet(PDF) 10 Page - Texas Instruments |
|
|
bq27425YZFR-G1 Datasheet(HTML) 10 Page - Texas Instruments |
10 / 32 page bq27425-G1 SLUSAI6 – NOVEMBER 2011 www.ti.com CONTROL_STATUS: 0x0000 Instructs the fuel gauge to return status information to control addresses 0x00/0x01. The status word includes the following information. Table 3. CONTROL_STATUS Bit Definitions bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 High Byte RSVD RSVD SS CALMODE CCA BCA QMAX_UP RES_UP Low Byte RSVD HIBERNATE RSVD SLEEP LDMD RUP_DIS VOK RSVD RSVD = Reserved. SS = Status bit indicating the bq27425 is in the SEALED State. Active when set. CALMODE = Status bit indicating the bq27425 is in calibration mode. Active when set. Status bit indicating the bq27425 Coulomb Counter Auto-Calibration routine is active. The CCA routine will take place CCA = approximately 3 minutes and 45 seconds after the initialization. Active when set. BCA = Status bit indicating the bq27425 board calibration routine is active. Active when set. Status bit indicating Qmax has Updated. True when set. This bit is cleared after power on reset or when [BAT_DET] bit is QMAX_UP = set. When this bit is cleared, it enables fast learning of battery Qmax. Status bit indicating that resistance has been updated. True when set. This bit is cleared after power on reset or when RES_UP = [BAT_DET] bit is set. Also this bit can only be set after Qmax is updated or QMAXU is set. When this bit is cleared, it enables fast learning of battery impedance. HIBERNATE = Status bit indicating a request for entry into HIBERNATE from SLEEP mode has been issued. True when set. Default is 0. SLEEP = Status bit indicating the bq27425 is in SLEEP mode. True when set. Status bit indicating the algorithm is using constant-power mode. True when set. Default is 1. Note: The bq27425 always LDMD = uses constant-power mode. RUP_DIS = Status bit indicating the bq27425 Ra table updates are disabled. Updates disabled when set.. VOK = Status bit indicating cell voltages are OK for Qmax updates. True when set. DEVICE_TYPE: 0x0001 Instructs the fuel gauge to return the device type to addresses 0x00/0x01. FW_VERSION: 0x0002 Instructs the fuel gauge to return the firmware version to addresses 0x00/0x01. HW_VERSION: 0x0003 Instructs the fuel gauge to return the hardware version to addresses 0x00/0x01. PREV_MACWRITE: 0x0007 Instructs the fuel gauge to return the previous command written to addresses 0x00/0x01. The value returned is limited to less than 0x0015. BAT_INSERT: 0X000C This subcommand forces the Flags() [BAT_DET] bit to set when the battery insertion detection is disabled via OpConfig[BIE=0]. In this case, the gauge does not detect battery insertion from the BIN pin ’s logic state, but relies on the BAT_INSERT host subcommand to indicate battery presence in the system. This subcommand also starts Impedance Track ™ gauging. BAT_REMOVE: 0X000D This subcommand forces the Flags() [BAT_DET] bit to clear when the battery insertion detection is disabled via OpConfig[BIE=0]. In this case, the gauge does not detect battery removal from the BIN pin ’s logic state, but relies on the BAT_REMOVE host subcommand to indicate battery removal from the system. 10 Copyright © 2011, Texas Instruments Incorporated |
Similar Part No. - bq27425YZFR-G1 |
|
Similar Description - bq27425YZFR-G1 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |