MC74LVQ652

MOTOROLA

LVQ DATA

BR1478

4

ABSOLUTE MAXIMUM RATINGS*

Symbol

Parameter

Value

Condition

Unit

VCC

DC Supply Voltage

–0.5 to +7.0

V

VI

DC Input Voltage

–0.5

≤ VI ≤ VCC + 0.5V

V

VO

DC Output Voltage

–0.5

≤ VO ≤ VCC + 0.5

Output in HIGH or LOW State

V

IIK

DC Input Diode Current

–20

VI = –0.5V

mA

+20

VI = VCC + 0.5V

mA

IOK

DC Output Diode Current

–20

VO = –0.5V

mA

+20

VI = VCC + 0.5V

mA

IO

DC Output Source/Sink Current

±50

mA

ICC

DC Supply Current

±400

mA

IGND

DC Ground Current

±400

mA

TSTG

Storage Temperature Range

–65 to +150

°C

* Absolute maximum continuous ratings are those values beyond which damage to the device may occur. Exposure to these conditions or

conditions beyond those indicated may adversely affect device reliability. Functional operation under absolute–maximum–rated conditions is

not implied.

RECOMMENDED OPERATING CONDITIONS

Symbol

Parameter

Min

Typ

Max

Unit

VCC

Supply Voltage

2.0

3.3

3.6

V

VI

Input Voltage

0

VCC

V

VO

Output Voltage

0

VCC

V

TA

Operating Free–Air Temperature

–40

+85

°C

∆V/∆t

Input Transition Rise or Fall Rate, VIN from 0.8V to 2.0V, VCC = 3.0V

0

125

mV/ns

DC ELECTRICAL CHARACTERISTICS

TA = –40°C to +85°C

Symbol

Characteristic

Condition

Min

Max

Unit

VIH

HIGH Level Input Voltage (Note 1)

2.7V

≤ VCC ≤ 3.6V,

VO = 0.1V or VCC – 0.1V

2.0

V

VIL

LOW Level Input Voltage (Note 1)

2.7V

≤ VCC ≤ 3.6V,

VO = 0.1V or VCC – 0.1V

0.8

V

VOH

HIGH Level Output Voltage

2.7V

≤ VCC ≤ 3.6V; IOH = –50µA

VCC – 0.1

V

VCC = 2.7V; IOH = –12mA

2.2

VCC = 3.0V; IOH = –12mA

2.48

VOL

LOW Level Output Voltage

2.7V

≤ VCC ≤ 3.6V; IOL = 50µA

0.1

V

2.7V

≤ VCC ≤ 3.6V; IOL= 12mA

0.4

II

Input Leakage Current

2.7V

≤ VCC ≤3.6V; VI= VCC, GND

±1.0

µA

IOZT

Maximum I/O Leakage Current

VI(OE) = VIL, VIH; VI, VO= VCC, GND

±3

µA

IOLD

Minimum Dynamic Output Current (Note 2)

VCC = 3.6V; VOLD = 0.8V Max

36

mA

IOHD

VCC = 3.6V; VOHD = 2.0V Min

–25

mA

ICC

Quiescent Supply Current

2.7V

≤ VCC ≤3.6V; VI = VCC, GND

10

µA

1. These values of VI are used to test DC electrical characteristics only. Functional test should use VIH ≥ 2.4V, VIL ≤ 0.5V.

2. Incident wave switching on transmission lines with impedances as low as 75

Ω for commercial temperature range is guaranteed. Maximum test

duration is 2ms, one output loaded at a time.