E

NV

VIIR

RO

ON

NM

ME

EN

NT

TA

ALL

S

AT

TIIO

ON

NS

S

O

UT

TLLIIN

NE

E

D

AW

WIIN

NG

G

P

N

O

UT

T

C

HA

AR

RT

T

;; C

AS

SE

E

A

A11

P

HY

YS

SIIC

CA

ALL

C

HA

AR

RA

AC

CT

TE

ER

RIIS

ST

TIIC

CS

S

Unit/Comments

2.0 X 2.0 X 0.4 inches

(51.0 X 51.0 X 10.2 mm)

Coated Copper

2.8 oz (79 grams)

6-sided, Continuous

Negative Input, Pin 3

Positive Input, Pin 4

>705,000 Hrs

Case Size

Case Material

Weight

Shielding

Shielding Connection

12V and 24V Input Models

48V Input Models

Reliability Specs: MTBF, Ground

Unit/Comments

o

C; Ambient

o

C; Ambient

o

C; Ambient

Free-Air Convection

Six-sided Metal

Case

Operating Temp. Range

(Industrial)

Max. Case Temp.

Storage Temp. Range

Relative Humidity

Cooling

EMI/RFI

Min

-55

-55

Typ

Max

+85

+100

+125

Notes:

1. Unless otherwise specified dimensions are in inches (mm).

Tolerances

Inches

mm

X.XX = ±0.02

X.X = ±0.5

X.XXX= ±0.010

X.XX = ±0.25

0.40

(10.2)

0.40

(10.2)

0.40

(10.2)

0.40

(10.2)

2.00 (50.8)

0.10

(2.5)

0.040±.005

(1.01)

DIA.

BOTTOM

8

7

6

5

4

3

2

1

0.10

(2.5)

2.00

(50.8)

SIDE

0.90

(22.9)

.20

(5.1)

.20

(5.1)

.20

(5.1)

0.15MIN.

(3.8)

0.40

(10.2)

C

AS

SE

E

A

A

C

AS

SE

E

A

A11

P

N

O

UT

T

C

HA

AR

RT

T

;; C

AS

SE

E

A

A

Single

Remote On/Off

Sync

- Vin

+ Vin

Trim

- Vout

+ Vout

No Pin

Dual

Remote On/Off

Sync

- Vin

+ Vin

Trim

- Vout

Common

+ Vout

Triple

Remote On/Off

Sync

- Vin

+ Vin

- Vout (Aux)

Common

-5V Vout

+Vout (Aux)

Pin

1

2

3

4

5

6

7

8

Pins

1

2

3

4

5

Single

+Vin

- Vin

+ Vout

Trim -

- Vout

Dual

+ Vin

- Vin

+ Vout

+/- Common

- Vout

All specifications are typical at nominal input, nominal load and 25

External, low ESR, 10 microfarad (minimum) capacitor across output is recommended for operation.

>> 2

Per MIL-STD-801E, method 507.3, procedure I.

Natural non-hazardous items, cycle 1,240 Hrs

SIDE

BOTTOM

0.40

(10.2)

2.00 (50.8)

0.15MIN.

(3.8)

2.00

(50.8)

0.60

(15.2)

0.40

(10.2)

0.40

(10.2)

0.20

(5.1)

0.90

(22.9)

0.040±.005

(1.01)

DIA.

0.80

(20.3)

3

4

5

1

2

0.60

(15.2)

Ordering Information:

1. Case “A” pinning is standard. Models with Case “A”

packaging do not require a suffix on the part number.

2. Case “A1” is an alternate. Models with Case “A1”

packaging must be designated with an “A1” suffix;

e.g. 1615D48XA-A1.

www.make-ps.com

E-mail:info@make-ps.com