 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
TUSB1310 Datasheet(PDF) 11 Page - Texas Instruments |
|
||||||||||||||||||||||||||||||
TUSB1310 Datasheet(HTML) 11 Page - Texas Instruments |
|
|
11 / 36 page  TUSB1310 www.ti.com SLLSE16C – DECEMBER 2009 – REVISED AUGUST 2010 Table 2-2. PIPE Signal Description (continued) SIGNAL NAME TYPE BALL NO. DESCRIPTION RX_DATA15 B9 RX_DATA14 A9 RX_DATA13 A8 RX_DATA12 B8 RX_DATA11 B5 RX_DATA10 B4 RX_DATA9 A4 Parallel USB SuperSpeed data output bus. RX_DATA8 B3 O The 16 bits represent 2 symbols of receive data where RX_DATA7-0 is the first symbol RX_DATA7 A3 received, and RX_DATA15-8 is the second. RX_DATA6 A2 RX_DATA5 B1 RX_DATA4 C2 RX_DATA3 C1 RX_DATA2 D1 RX_DATA1 D2 RX_DATA0 E2 RX_DATAK1 B7 Data/Control for the symbols of receive data. RX_DATAK0 corresponds to the low-byte of O RX_DATA, RX_DATAK1 to the upper byte. A value of zero indicates a data byte; a value RX_DATAK0 A7 of 1 indicates a control byte. RX_VALID O F1 Active High. Indicates symbol lock and valid data on RX_DATA and RX_DATAK. CONTROL AND STATUS SIGNALS PHY_RESETN I, PU J3 Active Low. Resets the transmitter and receiver. This signal is asynchronous. Active High. Used to tell the PHY to begin a receiver detection operation or to begin TX_DETRX_LPBK I, PD M6 loopback. TX_ELECIDLE I K3 Active High. Forces TX output to electrical idle depending on the power state. S, I/O, Active High. While de-asserted with the PHY in P0, P1, P2, or P3, indicates detection of RX_ELECIDLE F3 PD LFPS. Encodes receiver status and error codes for the received data stream when receiving RX_STATUS2 C7 data. O RX_STATUS1 C6 BIT 2 BIT 1 BIT 0 DESCRIPTION RX_STATUS0 C5 0 0 0 Received data OK 0 0 1 1 SKP ordered set added 0 1 0 1 SKP ordered set removed 0 1 1 Receiver detected 1 0 0 8B/10B decode error 1 0 1 Elastic buffer overflow Elastic buffer underflow. 1 1 0 This error code is not used if the elasticity buffer is operating in the nominal buffer empty mode. 1 1 1 Receive disparity error POWER_DOWN1 G3 Power up and down the transceiver power states. I POWER_DOWN0 H3 BIT 1 BIT 0 DESCRIPTION 0 0 P0, normal operation 0 1 P1, low recovery time latency, power saving state 1 0 P2, longer recovery time latency, low power state 1 1 P3, lowest power state When transitioning from P3 to P0, the signaling is asynchronous. Copyright © 2009–2010, Texas Instruments Incorporated PIN DESCRIPTIONS 11 Submit Documentation Feedback Product Folder Link(s): TUSB1310 |
Similar Part No. - TUSB1310_1 |
|
Similar Description - TUSB1310_1 |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
