E5AN/E5EN

10

USB-Serial Conversion Cable

Note: A driver must be installed in the personal computer. Refer to

installation information in the operation manual for the

Conversion Cable.

Communications Specifications

* The baud rate, data bit length, stop bit length, and vertical parity can

be individually set using the Communications Setting Level.

Current Transformer (Order Separately)

Ratings

Heater Burnout Alarms, SSR Failure

Alarms, and Heater Overcurrent Alarms

*1. For heater burnout alarms, the heater current will be measured

when the control output is ON, and the output assigned to the

alarm 1 function will turn ON if the heater current is lower than the

set value (i.e., heater burnout detection current value).

*2. For SSR failure alarms, the heater current will be measured when

the control output is OFF, and the output assigned to the alarm 1

function will turn ON if the heater current is higher than the set

value (i.e., SSR failure detection current value).

*3. For heater overcurrent alarms, the heater current will be

measured when the control output is ON, and the output assigned

to the alarm 1 function will turn ON if the heater current is higher

than the set value (i.e., heater overcurrent detection current

value).

Electrical Life Expectancy Curve for

Relays (Reference Values)

Note: Do not connect a DC load to a Controller with a Long-life Relay

Output.

Applicable OS

Windows 2000, XP, or Vista

Applicable software

CX-Thermo version 4 or higher

Applicable models

E5AN/E5EN/E5CN/E5CN-U/E5AN-

H/E5EN-H/E5CN-H/E5GN

USB interface standard

Conforms to USB Specification 1.1.

DTE speed

38400 bps

Connector specifications

Computer: USB (type A plug)

Temperature Controller: Setup Tool

port (on bottom of Controller)

Power supply

Bus power (Supplied from USB host

controller.)

Power supply voltage

5 VDC

Current consumption

70 mA

Ambient operating

temperature

0 to 55°C (with no condensation or

icing)

Ambient operating humidity 10% to 80%

Storage temperature

−20 to 60°C (with no condensation

or icing)

Storage humidity

10% to 80%

Altitude

2,000 m max.

Weight

Approx. 100 g

Transmission line

connection method

RS-485: Multipoint

RS-232C: Point-to-point

Communications

RS-485 (two-wire, half duplex) or RS-

232C

Synchronization method Start-stop synchronization

Protocol

CompoWay/F, SYSWAY, or Modbus

Baud rate

1200, 2400, 4800, 9600, 19200, 38400,

or 57600 bps

Transmission code

ASCII

Data bit length

*

7 or 8 bits

Stop bit length

*

1 or 2 bits

Error detection

Vertical parity (none, even, odd)

Frame check sequence (FCS) with

SYSWAY

Block check character (BCC) with

CompoWay/F or CRC-16 Modbus

Flow control

None

Interface

RS-485, RS-232C

Retry function

None

Communications buffer

217 bytes

Communications

response wait time

0 to 99 ms

Default: 20 ms

Dielectric strength

1,000 VAC for 1 min

Weight

E54-CT1: Approx. 11.5 g,

E54-CT3: Approx. 50 g

Accessories

(E54-CT3 only)

Armatures (2)

Plugs (2)

CT input (for heater

current detection)

Models with detection for single-

phase heaters: One input

Models with detection for single-

phase or three-phase heaters: Two

inputs

Maximum heater current

50 A AC

Input current indication

accuracy

±5% FS ±1 digit max.

Heater burnout alarm

setting range

*1

0.1 to 49.9 A (in units of 0.1 A)

Minimum detection ON time: 100 ms

SSR failure alarm setting

range

*2

0.1 to 49.9 A (in units of 0.1 A)

Minimum detection OFF time: 100 ms

Heater overcurrent alarm

setting range

*3

0.1 to 49.9 A (in units of 0.1 A)

Minimum detection ON time: 100 ms

500

300

100

50

30

10

5

3

1

0

12345

6

E5AN/E5EN

250 VAC, 30 VDC

(resistive load)

cos

φ = 1

Switching current (A)