Electronic Components Datasheet Search
  English  ▼
ALLDATASHEET.COM

X  

AS1115 Datasheet(PDF) 10 Page - ams AG

Part # AS1115
Description  64 LEDs, I짼C Interfaced LED Driver with Keyscan
Download  24 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  AMSCO [ams AG]
Direct Link  http://www.ams.com
Logo AMSCO - ams AG

AS1115 Datasheet(HTML) 10 Page - ams AG

Back Button AS1115 Datasheet HTML 6Page - ams AG AS1115 Datasheet HTML 7Page - ams AG AS1115 Datasheet HTML 8Page - ams AG AS1115 Datasheet HTML 9Page - ams AG AS1115 Datasheet HTML 10Page - ams AG AS1115 Datasheet HTML 11Page - ams AG AS1115 Datasheet HTML 12Page - ams AG AS1115 Datasheet HTML 13Page - ams AG AS1115 Datasheet HTML 14Page - ams AG Next Button
Zoom Inzoom in Zoom Outzoom out
 10 / 24 page
background image
www.austriamicrosystems.com
Revision 1.03
10 - 24
AS1115
Datasheet - D e t a i l e d D e s c r i p t i o n
acknowledge bit on the last byte that has been clocked out of the slave. In this case, the slave must leave the
data line HIGH to enable the master to generate the STOP condition.
- Figure 19 on page 9 details how data transfer is accomplished on the I²C bus. Depending upon the state of the R/
W bit, two types of data transfer are possible:
- Master Transmitter to Slave Receiver. The first byte transmitted by the master is the slave address, followed by
a number of data bytes. The slave returns an acknowledge bit after the slave address and each received byte.
- Slave Transmitter to Master Receiver. The first byte, the slave address, is transmitted by the master. The slave
then returns an acknowledge bit. Next, a number of data bytes are transmitted by the slave to the master. The
master returns an acknowledge bit after all received bytes other than the last byte. At the end of the last received
byte, a not-acknowledge is returned. The master device generates all of the serial clock pulses and the START
and STOP conditions. A transfer is ended with a STOP condition or a repeated START condition. Since a
repeated START condition is also the beginning of the next serial transfer, the bus will not be released.
The AS1115 can operate in the following slave modes:
- Slave Receiver Mode. Serial data and clock are received through SDA and SCL. After each byte is received, an
acknowledge bit is transmitted. START and STOP conditions are recognized as the beginning and end of a serial
transfer. Address recognition is performed by hardware after reception of the slave address and direction bit.
- Slave Transmitter Mode. The first byte (the slave address) is received and handled as in the slave receiver
mode. However, in this mode the direction bit will indicate that the transfer direction is reversed. Serial data is
transmitted on SDA by the AS1115 while the serial clock is input on SCL. START and STOP conditions are recog-
nized as the beginning and end of a serial transfer.
I²C Device Self Addressing
If this feature is used, 2 of the 16 key readback nodes can be left open or shorted for self-addressing. This is done with
KEYA together with SEGG and SEGF. This two nodes cannot be used for key-readback in this case. After startup all
devices have the predefined adress 0000000. A single command for self-addressing will update all connected AS1115.
This command has to be done after startup or everytime the AS1115 gets disconnected from the supply. The I²C
address definition must be done with fixed connection, since I²C detection is excluded from debounce time of key reg-
isters.
I²C Device Address Byte
The address byte (see Figure 20) is the first byte received following the START condition from the master device.
Figure 20. I²C Device Address Byte
- The default slave address is factory-set to 0000000.
- The two LSB bits of the address byte are the device select bits, A0 to A1, which can be set by the self-adress
command after startup. A maximum of four devices with the same pre-set code can therefore be connected on
the same bus at one time.
- The last bit of the address byte (R/W) define the operation to be performed. When set to a 1 a read operation is
selected; when set to a 0 a write operation is selected.
Following the START condition, the AS1115 monitors the I²C bus, checking the device type identifier being transmitted.
Upon receiving the address code, and the R/W bit, the slave device outputs an acknowledge signal on the SDA line.
0
0
0
0
0
0
0
R/W
MSB
6
5
432
1
LSB
0
0
0
0
0
A1
A0
R/W
MSB
6
5
432
1
LSB
predefined address:
updated address:


Similar Part No. - AS1115

ManufacturerPart #DatasheetDescription
logo
ams AG
AS1115 AMSCO-AS1115 Datasheet
3Mb / 26P
   64 LEDs, IC Inter faced LED Dr iver wi th Keyscan
logo
TEXAS ADVANCED OPTOELEC...
AS1115 TAOS-AS1115 Datasheet
3Mb / 26P
   64 LEDs, I 짼C Inter faced LED Dr iver wi th Keyscan
logo
ams AG
AS1115-BQFT AMSCO-AS1115-BQFT Datasheet
3Mb / 26P
   64 LEDs, IC Inter faced LED Dr iver wi th Keyscan
AS1115-BSST AMSCO-AS1115-BSST Datasheet
3Mb / 26P
   64 LEDs, IC Inter faced LED Dr iver wi th Keyscan
AS1115 AMSCO-AS1115_12 Datasheet
3Mb / 26P
   64 LEDs, IC Inter faced LED Dr iver wi th Keyscan
More results

Similar Description - AS1115

ManufacturerPart #DatasheetDescription
logo
STMicroelectronics
STLED316S STMICROELECTRONICS-STLED316S_08 Datasheet
441Kb / 33P
   Serial-interfaced 6-digit LED controller with keyscan
logo
Unisonic Technologies
UL316 UTC-UL316 Datasheet
214Kb / 5P
   SERIAL-INTERFACED 6-DIGIT LED CONTROLLER IC WITH KEYSCAN
UL318 UTC-UL318 Datasheet
244Kb / 6P
   SERIAL-INTERFACED 10-DIGIT LED CONTROLLER IC WITH KEYSCAN
logo
ams AG
AS1115 AMSCO-AS1115_12 Datasheet
3Mb / 26P
   64 LEDs, IC Inter faced LED Dr iver wi th Keyscan
logo
TEXAS ADVANCED OPTOELEC...
AS1115 TAOS-AS1115 Datasheet
3Mb / 26P
   64 LEDs, I 짼C Inter faced LED Dr iver wi th Keyscan
logo
OKI electronic componet...
MSM9006-01 OKI-MSM9006-01 Datasheet
130Kb / 18P
   LCD Driver with Keyscan Function
logo
ELMOS Semiconductor AG
E522.46 ELMOS-E522.46 Datasheet
308Kb / 2P
   8 Channel LED Driver with I짼C Interface
logo
Holtek Semiconductor In...
HT16K33 HOLTEK-HT16K33 Datasheet
1Mb / 47P
   RAM Mapping 16*8 LED Controller Driver with keyscan
logo
Maxim Integrated Produc...
MAX6958 MAXIM-MAX6958 Datasheet
270Kb / 19P
   2-Wire Interfaced, 3V to 5.5V, 4-Digit, 9-Segment LED Display Drivers with Keyscan
Rev 0; 10/02
MAX6958 MAXIM-MAX6958_V01 Datasheet
685Kb / 19P
   2-Wire Interfaced, 3V to 5.5V, 4-Digit 9-Segment LED Display Drivers with Keyscan
2005
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24


Datasheet Download

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com