345

Your dependable power partner – www.powerbox.com.au

Medline 200 Series

150-200 W A TTS SINGLE & MUL TIPLE OUTPUT AC/DC MEDICAL

PFD signal

TTL logic high for normal operation and TTL logic low

upon loss of input power. This signal appears at least

1ms prior to +5V output dropping 5% below its

nominal value. This signal also provides a minimum

delay of 100ms after +5V is within regulation

Efficiency

70% min on all models

Hold up time

20ms min at 110VAC

Line regulation

± 0.5% max at full load

ENVIRONMENTAL

Operating Temperature

0°C to 70°C

Storage temperature

–40°C to +85°C

Humidity

5% to 95% non-condensing

Derating

Derate from 100% at +50°C linearly to 50% at

+70°C.

Cooling

25CFM forced air, provided on “C” version, to be

provided for “B” version by user

GENERAL

Switching frequency

88-112kHz.

MTBF

350,000 hours at full load 25°C ambient ,

calculated per MIL-HDBK-217F

STANDARDS AND APPROVALS

Safety standards

IEC60601-1 TUV EN60601-1, EN60601-1

C-Tick

AS/NZS CISPR11 Group 1, Class A

EMC standards

EN55011 Class B, FCC Class B,VCII, EN61000-3-2, -3,

EN60001-4-2, -3, -4, -5, -6, -8, -11

MECHANICAL

Dimensions

See drawing

Weight

0.82kg for “B” version

0.96kg for version “C” version

Specifications

INPUT

Voltage range

90-260VAC

Frequency

47-63Hz.

Input Current

3.2A (rms) at 115VAC

1.6A (rms) at 230VAC

Leakage current

90µA max at 115VAC, 60Hz

150A max at 230VAC, 50Hz

Inrush Current

20A @ 115V or 40A at 230V at 25°C and cold start

Isolation

Input – Output: 4000VAC

Input – Ground: 1500VAC

Output – Ground: 500VAC

OUTPUT

Power

200W

Voltage

See table

Current

See table

Ripple & Noise

2% p-p max

Overvoltage protection

Provided on output #1 only, set at 112-132% of it

nominal output voltage

Overcurrent Protection

The output protected to short circuit conditions

Temperature coefficient

0.04%°C all outputs

Transient response

Max excursion of 4% or better on all models,

recovering to 1% of final value within 500us after

a 25% step load change

Technical Illustration

Notes:

1. Dimensions shown in inches (mm)

2. Tolerance 0.02 (0.5) maximum

3. Input connector P1 is Dinkle DT-35-B01W-09 screws are M3, nickle plated

4. Connector P3 mates with Molex housing 22-01-1043 and Molex 40445 series

crimp terminal

5. Connector P4/P5 mates with Molex housing 22-01-1023 and Molex 40445

series crimp terminal

6. P4 is for DC fan rated 24V/0.2A (models PM201/27), or 5V/0.38A (models

PM201-40-3), and 12V/0.2A (other models, Pin1 +V and Pin2 COM

7. Weight:

0.82 Kgs (1.83 Lbs) approx for “B” version

0.96 Kgs (2.14 Lbs) approx for “C” version

Features

• Low safety ground leakage current

• Wide input range 90 to 260Vac

• Input surge current protection

• Overvoltage protection

• Overcurrent protection

• Power fail detection (PFD) signal

• Optional cover and fan assembly

• 100% burn-in at full rated load

• Remote inhibit - TTL high disables output

• Short curcuit protection