E L E C T R O N I C S I N C .

5 Tap High Speed CMOS (HCT)

Compatible Active Delay Lines

TEL: (818) 892-0761

FAX: (818) 894-5791

http://www.pca.com

PCA ELECTRONICS, INC.

16799 SCHOENBORN ST.

NORTH HILLS, CA 91343

EP9604-XX & EP9604-XX-RC

Product performance is limited to specified parameters. Data is subject to change without prior notice.

Unless Otherwise Specified Dimensions are in Inches /mm ± .010 /.25

CS9604-XX & -RC

Rev. C1

12/5/05 RR

Schematic

Package

Add “-RC” after part number for RoHS Compliant

Tap Delays

(†±5% or ± 2nS)

12*

12*

12*

12*

12*

12*

12*

15

20

25

30

35

40

50

60

70

Total Delay

(†±5% or ± 2nS)

32

36

40

44

48

52

60

75

100

125

150

175

200

250

300

350

PCA

Part Number

EP9604-400(-RC)

EP9604-420(-RC)

EP9604-440(-RC)

EP9604-450(-RC)

EP9604-500(-RC)

EP9604-550(-RC)

EP9604-600(-RC)

EP9604-650(-RC)

EP9604-700(-RC)

EP9604-750(-RC)

EP9604-800(-RC)

EP9604-850(-RC)

EP9604-900(-RC)

EP9604-950(-RC)

EP9604-1000(-RC)

Tap Delays

(†±5% or ± 2nS)

Total Delay

(†±5% or ± 2nS)

400

420

440

450

500

550

600

650

700

750

800

850

900

950

1000

PCA

Part Number

EP9604-32(-RC)

EP9604-36(-RC)

EP9604-40(-RC)

EP9604-44(-RC)

EP9604-48(-RC)

EP9604-52(-RC)

EP9604-60(-RC)

EP9604-75(-RC)

EP9604-100(-RC)

EP9604-125(-RC)

EP9604-150(-RC)

EP9604-175(-RC)

EP9604-200(-RC)

EP9604-250(-RC)

EP9604-300(-RC)

EP9604-350(-RC)

†Whichever is greater. *Inherent Delay • Delay times referenced from input to leading edges at 25°C, 5.0V.

Input Pulse Test Conditions @ 25° C

EIN

Pulse Input Voltage

PW

Pulse Width % of Total Delay

TRI

Pulse Rise Time (0.75 - 2.4 Volts)

PRR Pulse Repetition Rate @ Td ≤ 500 nS

Pulse Repetition Rate @ Td > 500 nS

VCC Supply Voltage

3.2

150

2.0

1.0

100

5.0

Unit

Volts

%

nS

MHz

KHz

Volts

12

4

10

6

8

1

7

OUTPUT

GROUND

INPUT

14

VCC

Notes :

2. Peak Solder Rating

(per JEDEC22-B102D)

4. Weight

3. Moisture Sensitive Levels (MSL)

(per JEDEC22-B102D)

1. Assembly Process

(Solder Composition)

(Leadframe)

(Assembly Solder)

5. Packaging Information

(Tube)

EP9604-XX-RC

260°C

TBD grams

4

(72 hours,

≤30°C/60%RH)

SnPb

(RoHS exemption 7a)

Sn

27 pieces/tube

EP9604-XX

260°C

TBD grams

3

(168 hours,

≤30°C/60%RH)

SnPb

SnPb

27 pieces/tube

17

18

19

20

21

22

24

30

40

50

60

70

80

100

120

140

22

24

26

28

30

32

36

45

60

75

90

105

120

150

180

210

27

30

33

36

39

42

48

60

80

100

120

140

160

200

240

280

80

84

88

90

100

110

120

130

140

150

160

170

180

190

200

160

168

176

180

200

220

240

260

280

300

320

340

360

380

400

240

252

264

270

300

330

360

390

420

450

480

510

540

570

600

320

336

352

360

400

440

480

520

560

600

640

680

720

760

800

DC Electrical Characteristics

Parameter

Test Conditions

Unit

VIH

High Level Input Voltage

VCC = 4.5 to 5.5

Volt

VIL

Low Level Input Voltage

VCC = 4.5 to 5.5

Volt

VOH High Level Output Voltage

VCC = 4.5V,I O= -4.0mA

Volt

@ V IH or VIL

VOL

Low Level Output Voltage

VCC = 4.5V,I O = 4.0mA

Volt

@ V IH or VIL

I L

Input Leakage Current

VCC = 5.5V @ V IH or V IL

uA

I CCL Supply Current

VCC = 5.5V, V IN = 0

mA

TRO

Output Rise Time

≤550 nS (.75 - 2.4 Volts)

nS

NH

High Fanout

LSTTL Load

VCC = 5.5V, V OH = 4.0V

Min.

2.0

4.0

10

>550 nS

Max.

0.8

0.3

±1.0

15

4

5

nS

Recommended Operating Conditions Min.

Max.

Unit

*These two values are inter-dependent.

VCC DC Supply Voltage

VI

DC Input Voltage Range

VO

DC Output Voltage Range

PW* Pulse Width % of Total Delay

D*

Duty Cycle

TA

Operating Free Air Temperature

I O

DC Output Source/Sink Current

4.5

0

0

40

-40

5.5

V CC

V CC

40

+85

25

Volt

Volt

Volt

%

%

°C

mA

.780 Max.

(19.81)

PCA

EP9604-XX(-RC)

Date Code

.010

(.254)

.150 (3.81)

.020 Min.

(.508)

.280 Max.

(7.11)

.250 Max.

(6.35)

.020 Typ.

(.508)

White Dot

Pin#1

.100

(2.54)

.300

(7.62)

.200

(5.08)

.365 Max.

(9.27)