Electronic Components Datasheet Search |
|
EMOD Datasheet(PDF) 3 Page - rfsolutions.ltd |
|
EMOD Datasheet(HTML) 3 Page - rfsolutions.ltd |
3 / 3 page A A DS-EMOD-3 Oct ’07 ©2007 RF Solutions Ltd, www.rfsolutions.co.uk Page 3 Tel 01273 898000 Fax 01273 480661 EMOD Waterproof Radio Remote Controls Series Learning a new Transmitter Encoder All systems are supplied pre-learnt, ready to operate. With this system each of a transmitters’ ‘buttons’ may be paired to one or many individual output relays on the receiver, as below. Up to 7 transmitters may be learnt to each receiver relay output. Please Note: During Learn and Erase the relays operate at high speed. They should be isolated from sensitive equipment during this process. 1. Decide which transmitter ‘button’ is to be paired with which receiver relay output. 2. Apply power the receiver and wait 10secs for the unit to enter ‘normal operation’ mode. 3. Switch the receiver unit OFF and then ON again in ~1sec intervals four times finally leaving the unit powered. 4. After 5 seconds 3 ‘clicks’ are heard. The unit is now in ‘learn’ Mode 5. The receiver will now cycle through all the relays in turn. For relay #1 one click will be heard For relay #2 two clicks will be heard For relay #3 three clicks will be heard For relay #4 four clicks will be heard 6. When you hear the number of “clicks” corresponding to the relay you wish to learn press the chosen transmitter button. 7. The receiver will acknowledge by sounding the “click(s)” according to the relay number learnt, e.g. 3 clicks to show relay 3 has been learnt. 8. Press that same transmitter button again, to confirm OK. The receiver will “click” again to confirm. 9. This then completes learning for this relay. The receiver will then move onto the next relay until either all relays have cycled through. Finally a shorter click will be heard to indicate that the learn cycle has been completed. 10. Wait 10 seconds for the unit to return to ‘normal operation’ mode. 11. The transmitter is now ‘learnt’ to the receiver unit and will operate the output relay(s) you have learnt. Erasing Transmitter Encoders form Memory 1. Power the receiver unit up and wait 10 seconds for the unit to enter ‘normal operation’ mode. 2. Switch the unit off and then on again in ~1 second intervals six times finally leaving the unit powered. 3. Wait 5 seconds until a ‘clicking’ sound is heard for a period of 10 seconds. 4. Wait 10 seconds for the receiver unit to return to ‘normal’ mode 5. The unit has now erased all encoder data. R F Solutions Ltd., Unit 21, Cliffe Industrial Estate, Lewes, E. Sussex. BN8 6JL. England. Email : sales@rfsolutions.co.uk http://www.rfsolutions.co.uk/ Tel: +44 (0)1273 898 000 Fax: +44 (0)1273 480 661 RF Solutions is a member of the Low Power Radio Association. Information contained in this document is believed to be accurate, however no representation or warranty is given and R.F. Solutions Ltd. assumes no liability with respect to the accuracy of such information. Use of R.F. Solutions as critical components in life support systems is not authorised except with express written approval from R.F. Solutions Ltd. |
Similar Description - EMOD |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |