Electronic Components Datasheet Search
Selected language     English  ▼
Part Name
         Description


TUSB2036 Datasheet(PDF) 5 Page - Texas Instruments

Click here to check the latest version.
Part No. TUSB2036
Description  2/3-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE
Download  20 Pages
Scroll/Zoom Zoom In 100% Zoom Out
Maker  TI [Texas Instruments]
Homepage  http://www.ti.com
Logo 

 
 5 page
background image
TUSB2036
2/3-PORT HUB FOR THE UNIVERSAL SERIAL BUS
WITH OPTIONAL SERIAL EEPROM INTERFACE
SLLS372 – MARCH 2000
5
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
Terminal Functions
TERMINAL
I/O
DESCRIPTION
NAME
VF
I/O
DESCRIPTION
BUSPWR
8
I
Power source indicator. BUSPWR is an active low input that indicates whether the downstream ports source
their power from the USB cable or a local power supply. For the bus-power mode, this pin should be pulled
low, and for the self-powered mode, this pin should be pulled to 3.3 V. Input must not change dynamically
during operation.
DM0
2
I/O
Root port USB differential data minus. DM0 paired with DP0 constitutes the upstream USB port.
DM1 – DM3
11, 15,
19
I/O
USB differential data minus. DM1 – DM3 paired with DP1 – DP3 support up to three downstream USB ports.
DP0
1
I/O
Root port USB differential data plus. DP0 paired with DM0 constitutes the upstream USB port.
DP0PUR
27
O
Pull-up resistor connection. Whenever a system reset occurs (RESET being driven to low, but not USB reset)
or any logic level change on BUSPWR terminal, DP0PUR output goes to inactive Low until the internal counter
reaches a 3 ms time period. After the counter expires, DP0PUR is driven to the VCC (3.3 V) level thereafter
until the next system reset event or BUSPWR logic level change.
DP1 – DP3
12, 16,
20
I/O
USB differential data plus. DP1 – DP3 paired with DM1 – DM3 support up to three downstream USB ports.
EECLK
5
O
EEPROM serial clock. When EXTMEM is high, the EEPROM interface is disabled. The EECLK pin is disabled
and should be left floating (unconnected). When EXTMEM is low, EECLK acts as a 3-state serial clock output
to the EEPROM with a 100
µA internal pulldown.
EEDATA/
GANGED
6
I/O
EEPROM serial data/power management mode indicator. When EXTMEM is high, EEDATA/GANGED
selects between gang and per-port power overcurrent detection for the downstream ports. When EXTMEM
is low, EEDATA/GANGED acts as a serial data I/O for the EEPROM and is internally pulled down with a
100
µA pulldown. This standard TTL input must not change dynamically during operation.
EXTMEM
26
I
EEPROM read enable. When EXTMEM is high, the serial EEPROM interface of the device is disabled. When
EXTMEM is low, terminals 5 and 6 are configured as the clock and data pins of the serial EEPROM interface,
respectively.
GND
7, 28
Ground. GND terminals must be tied to ground for proper operation.
OCPROT/
PWRSW
21
I
Overcurrent Protection for bus-powered hub (active low). /Power Switching for self-powered hub (active low).
The pin has a different meaning for the bus or self-powered hub. If the pin is logic-high the internal pull-down
is disabled. (see Notes 1 and 2 ).
OVRCUR1 –
OVRCUR3
10, 14,
18
I
overcurrent input. OVRCUR1 – OVRCUR3 are active low. For per-port overcurrent detection, one overcurrent
input is available for each of the three downstream ports. In the ganged mode, any OVRCUR input may be
used and all OVRCUR pins should be tied together. OVRCUR pins are active low inputs with noise filtering
logic. OVRCUR3 has an internal pull-up that can be enabled for the 2-port operation.
NOTES:
1. If the hub is implemented to be bus-powered (via BUSPWR tying to GND):
– TUSB2036 reports to the host that the hub end-product downstream ports are power-switched (this is required by the USB 1.1
Specification). Hub end product vendor has to ensure the actual end product implementation meets this specification requirement.
– Pin 21 acts as overcurrent protection (OCPROT) implementation indication pin for the bus-powered hub. The overcurrent
protection implementation is reported through the wHubCharacteristics. D4-bit in the hub descriptor.
– When OCPROT is low, the TUSB2036 reports to the host that the hub end-product provides overcurrent protection and the
wHubCharacteristics. D4-bit is set to 0.
– When OCPROT is high, the TUSB2036 reports to the host that the hub end-product does not provide overcurrent protection
and the wHubCharacteristics. D4-bit is set to 1.
2. If the hub is implemented to be self-powered (via BUSPWR tying to 3.3-V VCC),:
– TUSB2036 reports to the host that the hub end-product provides overcurrent protection to the downstream ports (this is required
by the USB 1.1 Specification). Hub end product vendor has to ensure the actual end-product implementation meets this
specification requirement.
– Pin 21 acts as power switching (PWRSW) implementation indication pin for the self-powered hub. The power switching
implementation is reported through the bPwrOn2PwrGood field in the hub descriptor.
– When PWRSW is low, the TUSB2036 reports to the host that the hub end-product has port power switching at the downstream
ports and the bPwrOn2PwrGood is set to 50 units (100 ms).
– When PWRSW is high, the TUSB2036 reports to the host that the hub end-product does not have port power switching at the
downstream ports and the bPwrOn2PwrGood is set to 0 units (0 ms).




Html Pages

1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18  19  20 


Datasheet Download



Related Electronics Part Number

Part NumberComponents DescriptionHtml ViewManufacturer
TUSB2040A4-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE 1 2 3 4 5 MoreTexas Instruments
TUSB20434-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE 1 2 3 4 5 MoreTexas Instruments
TUSB20464-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE 1 2 3 4 5 MoreTexas Instruments
TUSB2046A4-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE 1 2 3 4 5 MoreTexas Instruments
TUSB2046B4-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE 1 2 3 4 5 MoreTexas Instruments
TUSB2077A7-PORT HUB FOR THE UNIVERSAL SERIAL BUS WITH OPTIONAL SERIAL EEPROM INTERFACE 1 2 3 4 5 MoreTexas Instruments
WT62P1microcontroller for digital controlled monitor with Universal Serial Bus USB interface 1 2 3 4 5 MoreList of Unclassifed Manufacturers
FM93CS46 MICROWIRE™ Bus Interface 1024-Bit Serial EEPROM with Data Protect and Sequential Read 1 2 3 4 5 MoreFairchild Semiconductor
NM93CS46 MICROWIRE™ Bus Interface 1024-Bit Serial EEPROM with Data Protect and Sequential Read 1 2 3 4 5 MoreFairchild Semiconductor
FM93CS56 MICROWIRE™ Bus Interface 2048-Bit Serial EEPROM with Data Protect and Sequential Read 1 2 3 4 5 MoreFairchild Semiconductor

Link URL

Does ALLDATASHEET help your business so far?  [ DONATE ]  

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Bookmark   |   Link Exchange   |   Manufacturer List
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  , Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp  |   Russian : Alldatasheetru.com
Korean : Alldatasheet.co.kr   |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com  |   Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl