Page 2 of 4 Issued Date：2008/05/21

Output Current

Input Current

Model

Number

Input

Range

Output

Voltage Min. load Full load

Output

(4)

Eff

(4)

(%)

Load

regulation

QEB100-24S3P3

18 – 36 VDC

3.3 VDC

0mA

25A

100mVp-p

80mA

3997mA

89

10mV

QEB100-24S05

18 – 36 VDC

5 VDC

0mA

20A

100mVp-p

120mA

4845mA

90

15mV

QEB100-24S12

18 – 36 VDC

12 VDC

0mA

8.33A

100mVp-p

130mA

4843mA

90

36mV

QEB100-24S15

18 – 36 VDC

15 VDC

0mA

6.67A

100mVp-p

190mA

4847mA

90

45mV

QEB100-48S1P8

36 – 75 VDC

1.8 VDC

0mA

30A

100mVp-p

70mA

1389mA

85

5.4mV

QEB100-48S2P5

36 – 75 VDC

2.5 VDC

0mA

30A

100mVp-p

70mA

1883mA

87

7.5mV

QEB100-48S3P3

36 – 75 VDC

3.3 VDC

0mA

25A

100mVp-p

75mA

2022mA

89

10mV

QEB100-48S05

36 – 75 VDC

5 VDC

0mA

20A

100mVp-p

80mA

2422mA

90

15mV

QEB100-48S12

36 – 75 VDC

12 VDC

0mA

8.33A

100mVp-p

130mA

2422mA

90

36mV

QEB100-48S15

36 – 75 VDC

15 VDC

0mA

6.67A

100mVp-p

130mA

2424mA

90

45mV

Note :

1.BELLCORE TR-NWT-000332. Case 1: 80% Stress, Temperature at 40ºC.

MIL-HDBK-217F Notice2 @Ta=25 ºC, Full load(Ground, Benign, controlled environment)

2.Maximum value at nominal input voltage and full load of standard type.

3.Typical value at nominal input voltage and no load.

4.Typical value at nominal input voltage and full load.

5.Maximum output deviation is 10% inclusive of trim. If remote sense is not being used, the + sense should be connected to its corresponding

+OUTPUT and likewise the –sense should be connected to its corresponding –OUTPUT.

6.The positive logic and pin length are optional ( see table ). The pin voltage is referenced to –Vin.

7.Heat sink is optional and P/N：7G-0029A-F, 7G-0030A-F, 7G-0031A-F, 7G-0032A-F.

8.The QEB100 meets EN55022 class A and class B only with external components connected before the input pin to the converter.

9.An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5.

The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220μF/100V, ESR 48mΩ.

10.BASEPLATE GROUNDING：Base-plate should be grounded at one of the four screw bolts prior to operation.

11.The converter is provided by basic insulation.