Key Features:

F2500RW

2:1 Input 25W - 30W

Single & Dual Output

DC/DC Converters

Series

Electrical Specifications

Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.

Input

Parameter

Conditions

Min.

Typ.

Max.

Units

Input Start Voltage

12 VDC Input

8.6

8.8

9.0

VDC

24 VDC Input

17.0

17.5

18.0

48 VDC Input

34.0

35.0

36.0

Under Voltage Shutdown

12 VDC Input

8.1

8.3

8.5

VDC

24 VDC Input

16.0

16.5

17.0

48 VDC Input

32.0

33.0

34.0

Input Filter

(Pi) Filter (Meets EN55022 Class “A”)

Reverse Polarity Input Current

2.0

A

Short Circuit Input Power

4,500

mW

Output

Parameter

Conditions

Min.

Typ.

Max.

Units

Output Voltage Accuracy

±0.5

±1.0

%

Output Voltage Balance

Dual Output , Balanced Loads

±0.5

±2.0

%

Line Regulation

For Vin Min to Max

±0.1

±0.3

%

Load Regulation

Iout = 50% to 100%

±0.1

±0.5

%

Ripple & Noise (20 MHz) (Note 1)

55

80

mV P - P

Ripple & Noise (20 MHz)

Over Line, Load & Temp.

100

mV P - P

Output Power Protection

110

160

%

Transient Recovery Time (Note 2)

25% Load Step Change

150

300

µSec

Transient Response Deviation

±2.0

±4.0

%

Temperature Coefficient

±0.01

±0.02

%/°C

Output Short Circuit

Continuous (Autorecovery)

General

Parameter

Conditions

Min.

Typ.

Max.

Units

Isolation Voltage

60 Seconds

1,500

VDC

Isolation Resistance

500 VDC

1,000

M

Isolation Capacitance

100 kHz, 1V

1,200

1,500

pF

Switching Frequency

290

330

360

kHz

Over Temperature Protection

Case Temperature

107

112

117

°C

Parameter

Conditions

Min.

Typ.

Max.

Units

Supply On

2.5

100.0

VDC

Supply Off

-1.0

1.0

VDC

Standby Input Current

5mA

Control Common

Referenced to Negative Input (pin 2)

Environmental

Parameter

Conditions

Min.

Typ.

Max.

Units

Operating Temperature Range

Ambient

-40

+50

°C

Operating Temperature Range

Case

-40

+105

°C

Storage Temperature Range

-50

+125

°C

Cooling

Free Air Convection

Humidity

RH, Non-condensing

95

%

Physical

Case Size

2.0 x 1.6 x 0.37 Inches (50.8 x 40.6 x 9.3 mm)

Case Material

Metal with Non-Conductive Base

Weight

1.75 Oz (48g)

Reliability Specifications

Parameter

Conditions

Min.

Typ.

Max.

Units

MTBF

MIL HDBK 217F, 25°C, Gnd Benign

1,000

kHours

Absolute Maximum Ratings

Parameter

Conditions

Min.

Typ.

Max.

Units

Input Voltage Surge (1 Sec)

12 VDC Input

-0.7

25.0

VDC

24 VDC Input

-0.7

50.0

48 VDC Input

-0.7

100.0

Lead Temperature

1.5 mm From Case For 10 Sec

260

°C

Internal Power Dissipation

All Models

5,500

mW

Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.

www.micropowerdirect.com

MicroPower Direct

292 Page Street

Suite D

Stoughton, MA 02072

USA

T: (781) 344-8226

F: (781) 344-8481

E: sales@micropowerdirect.com

W: www.micropowerdirect.com