Model

Number

Input

Output

Load

Regulation

(%, Max)

Efficiency

(%, Typ)

Fuse Rating

Slow-Blow

(mA)

Voltage (VDC)

Current (mA)

Voltage

(VDC)

Current

(mA, Max)

Current

(mA, Min)

Nominal

Range

Full-Load

No-Load

D101E

5

4.5 - 5.5

278

30

5.0

200.0

20.0

15

72

500

D102E

5

4.5 - 5.5

270

30

9.0

111.0

12.0

15

74

500

D103E

5

4.5 - 5.5

260

30

12.0

83.0

9.0

15

77

500

D104E

5

4.5 - 5.5

253

30

15.0

67.0

7.0

15

79

500

D105E

5

4.5 - 5.5

278

30

±5.0

±100.0

±10.0

15

72

500

D106E

5

4.5 - 5.5

267

30

±9.0

±56.0

±6.0

15

75

500

D107E

5

4.5 - 5.5

256

30

±12.0

±42.0

±5.0

15

78

500

D108E

5

4.5 - 5.5

253

30

±15.0

±33.0

±4.0

15

79

500

D111E

12

10.8 - 13.2

114

15

5.0

200.0

20.0

15

73

200

D112E

12

10.8 - 13.2

111

15

9.0

111.0

12.0

15

75

200

D113E

12

10.8 - 13.2

105

15

12.0

83.0

9.0

15

79

200

D114E

12

10.8 - 13.2

104

15

15.0

67.0

7.0

15

80

200

D115E

12

10.8 - 13.2

113

15

±5.0

±100.0

±10.0

15

74

200

D116E

12

10.8 - 13.2

110

15

±9.0

±56.0

±6.0

15

76

200

D117E

12

10.8 - 13.2

105

15

±12.0

±42.0

±5.0

15

79

200

D118E

12

10.8 - 13.2

104

15

±15.0

±33.0

±4.0

15

80

200

D121E

24

21.6 - 26.4

56

8

5.0

200.0

20.0

15

74

100

D122E

24

21.6 - 26.4

55

8

9.0

111.0

12.0

15

76

100

D123E

24

21.6 - 26.4

52

8

12.0

83.0

9.0

15

80

100

D124E

24

21.6 - 26.4

51

8

15.0

67.0

7.0

15

81

100

D125E

24

21.6 - 26.4

56

8

±5.0

±100.0

±10.0

15

74

100

D126E

24

21.6 - 26.4

55

8

±9.0

±56.0

±6.0

15

76

100

D127E

24

21.6 - 26.4

52

8

±12.0

±42.0

±5.0

15

80

100

D128E

24

21.6 - 26.4

51

8

±15.0

±33.0

±4.0

15

81

100

Derating Curve

Model Selection Guide

Mechanical Dimensions

Notes:

Pin

Single

Dual

Pin

Single

Dual

1

+Vin

+Vin

5

No Pin

Common

2

-Vin

-Vin

6

+Vout

+Vout

4

-Vout

-Vout

Notes:

1. Output load regulation is specified for a load change of 10% to 100%.

2. These units should not be operated with a load under 10% of full load.

Operation at no-load may cause damage to the unit.

3. These converters will operate without external components. However,

when measuring output ripple, it is recommended that an external

ceramic capacitor

be placed from the

+Vout pin to the

-Vout pin for single

output units and

from each output

to common for dual

output units. An in-

put capacitor will enhance stability over temperature and input line

variations. Recommended capacitor values are given in the table above.

For applications requiring very low output noise levels, a simple LC filter

should be effective.

4. Dual output units may be connected to provide a 10V, 18V, 24V or 30

VDC output. To do this, connect the load across the positive (+Vout) and

negative (-Vout) outputs and float the output common

5. It is recommended that a fuse be used on the input of a power supply for

protection. See the Model Selection table above for the correct rating.

Vin

Input

Capacitor

Vout

Output Capacitor

Single

Dual

5 VDC

4.7 μF

5 VDC

10.0 μF

4.7 μF

12 VDC

2.2 μF

9 VDC

4.7 μF

2.2 μF

24 VDC

1.0 μF

12 VDC

2.2 μF

1.0 μF

15 VDC

1.0 μF

0.47 μF

Other input/output combinations are available

(i.e. 3.3 VDC). Contact the factory for details at:

sales@micropowerdirect.com

Pin Connections

MicroPower Direct

www.micropowerdirect.com

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

•

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com