LTM4603HVIV-PBF datasheet(11/24 Pages) LINER

Part #	LTM4603HVIV-PBF

Description	6A, 28VIN DC/DC 關Module with PLL, Output Tracking and Margining

Download	24 Pages

Scroll/Zoom	100%

Manufacturer	LINER [Linear Technology]

Direct Link	http://www.linear.com

Logo

11 / 24 page

LTM4603HV

11

4603hvf

APPLICATIO S I FOR ATIO

or choose a capacitor rated at a higher temperature than

required. Always contact the capacitor manufacturer for

derating requirements.

In Figure 20, the 10μF ceramic capacitors are together

used as a high frequency input decoupling capacitor. In a

typical 6A output application, two very low ESR, X5R or

X7R, 10μF ceramic capacitors are recommended. These

decoupling capacitors should be placed directly adjacent

to the module input pins in the PCB layout to minimize

the trace inductance and high frequency AC noise. Each

10μF ceramic is typically good for 2A to 3A of RMS ripple

current. Refer to your ceramics capacitor catalog for the

RMS current ratings.

Multiphase operation with multiple LTM4603HV devices in

parallel will lower the effective input RMS ripple current due

to the interleaving operation of the regulators. Application

Note 77 provides a detailed explanation. Refer to Figure 2

for the input capacitor ripple current requirement as a func-

tion of the number of phases. The ﬁgure provides a ratio

of RMS ripple current to DC load current as a function of

duty cycle and the number of paralleled phases. Pick the

corresponding duty cycle and the number of phases to

arrive at the correct ripple current value. For example, the

2-phase parallel LTM4603HV design provides 10A at 2.5V

output from a 12V input. The duty cycle is DC = 2.5V/12V

= 0.21. The 2-phase curve has a ratio of ~0.25 for a duty

cycle of 0.21. This 0.25 ratio of RMS ripple current to a

DC load current of 10A equals ~2.5A of input RMS ripple

current for the external input capacitors.

Output Capacitors

The LTM4603HV is designed for low output voltage ripple.

The bulk output capacitors deﬁned as COUT are chosen

with low enough effective series resistance (ESR) to meet

the output voltage ripple and transient requirements. COUT

can be a low ESR tantalum capacitor, a low ESR polymer

capacitor or a ceramic capacitor. The typical capacitance is

200μF if all ceramic output capacitors are used. Additional

output ﬁltering may be required by the system designer,

if further reduction of output ripple or dynamic transient

spike is required. Table 2 shows a matrix of different output

voltages and output capacitors to minimize the voltage

droop and overshoot during a 3A/μs transient. The table

optimizes total equivalent ESR and total bulk capacitance

to maximize transient performance.

Multiphase operation with multiple LTM4603HV devices

in parallel will lower the effective output ripple current

due to the interleaving operation of the regulators. For

example, each LTM4603HV’s inductor current of a 12V to

2.5V multiphase design can be read from the “Inductor

Ripple vs Duty Cycle” (Figure 3). The large ripple current

at low duty cycle and high output voltage can be reduced

by adding an external resistor from fSET to ground which

increases the frequency. If we choose the duty cycle of

DC = 2.5V/12V = 0.21, the inductor ripple current for 2.5V

output at 21% duty cycle is ~2A in Figure 3.

Figure 2. Normalized Input RMS Ripple Current

vs Duty Factor for One to Six Modules (Phases)

Figure 3. Inductor Ripple Current vs Duty Cycle

DUTY FACTOR (VOUT/VIN)

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

0.6

0.5

0.4

0.3

0.2

0.1

0

4603HV F02

6-PHASE

4-PHASE

3-PHASE

2-PHASE

1-PHASE

DUTY CYCLE (VOUT/VIN)

0

1

2

3

4

20

40

60

80

4603HV F03

2.5V OUTPUT

5V OUTPUT

1.8V OUTPUT

1.5V OUTPUT

1.2V OUTPUT

3.3V OUTPUT WITH

82.5k ADDED FROM

VOUT TO fSET

5V OUTPUT WITH

150k ADDED FROM

fSET TO GND

Similar Part No. - LTM4603HVIV-PBF

Manufacturer	Part #	Datasheet	Description
Linear Technology	LTM4603HV	453Kb / 36P	24V, 15A Monolithic Step Down Regulator
Linear Technology	LTM4603HV	313Kb / 26P	6A, 28VIN DC/DC Module with PLL, Output Tracking and Margining

More results

Similar Description - LTM4603HVIV-PBF

Manufacturer	Part #	Datasheet	Description
Linear Technology	LTM4603HV	313Kb / 26P	6A, 28VIN DC/DC Module with PLL, Output Tracking and Margining
	LTM4601AHV	356Kb / 28P	12A, 28VIN DC/DC 關Module with PLL, Output Tracking and Margining
	LTM4601HV	383Kb / 28P	12A 28VIN DC/DC 關Module with PLL, Output Tracking and Margining
	LTM4603	340Kb / 24P	6A DC/DC 關Module with PLL, Output Tracking and Margining
Linear Dimensions Semic...	LTM4601HVIVPBF	520Kb / 30P	12A 28VIN DC/DC 關Module Regulator with PLL, Output Tracking and Margining
Linear Technology	LTM4601HV	520Kb / 30P	12A 28VIN DC/DC Module Regulator with PLL, Output Tracking and Margining
	LTM4601AHV	1,006Kb / 30P	12A, 28VIN DC/DC Module Regulator with PLL, Output Tracking and Margining
	LTM4603-1	448Kb / 26P	20V, 6A DC/DC Module Regulator with PLL, Output Tracking and Margining
	LTM4603	448Kb / 26P	20V, 6A DC/DC Module Regulator with PLL, Output Tracking and Margining
	LTM4601	389Kb / 28P	12A DC/DC 關Modules with PLL, Output Tracking and Margining

More results

LTM4603HVIV-PBF Datasheet(PDF) 11 Page - Linear Technology

LTM4603HVIV-PBF Datasheet(HTML) 11 Page - Linear Technology

Similar Part No. - LTM4603HVIV-PBF

Similar Description - LTM4603HVIV-PBF

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

Datasheet Download

Link URL