Electronic Components Datasheet Search |
|
AT25F512B-SSH-T Datasheet(PDF) 9 Page - ATMEL Corporation |
|
AT25F512B-SSH-T Datasheet(HTML) 9 Page - ATMEL Corporation |
9 / 34 page 9 3689C–DFLASH–12/08 AT25F512B [Preliminary] Figure 8-1. Byte Program Figure 8-2. Page Program 8.2 Block Erase A block of 4 or 32 Kbytes can be erased (all bits set to the logical “1” state) in a single operation by using one of three different opcodes for the Block Erase command. An opcode of 20h is used for a 4-Kbyte erase, and an opcode of 52h or D8h is used for a 32-Kbyte erase. Before a Block Erase command can be started, the Write Enable command must have been previously issued to the device to set the WEL bit of the Status Register to a logical “1” state. To perform a Block Erase, the CS pin must first be asserted and the appropriate opcode (20h, 52h, or D8h) must be clocked into the device. After the opcode has been clocked in, the three address bytes specifying an address within the 4- or 32-Kbyte block to be erased must be clocked in. Any additional data clocked into the device will be ignored. When the CS pin is deas- serted, the device will erase the appropriate block. The erasing of the block is internally self- timed and should take place in a time of t BLKE. Since the Block Erase command erases a region of bytes, the lower order address bits do not need to be decoded by the device. Therefore, for a 4-Kbyte erase, address bits A11-A0 will be ignored by the device and their values can be either a logical “1” or “0”. For a 32-Kbyte erase, address bits A14-A0 will be ignored by the device. Despite the lower order address bits not being decoded by the device, the complete three address bytes must still be clocked into the device before the CS pin is deasserted, and the CS pin must be deasserted on an even byte boundary (multiples of eight bits); otherwise, the device will abort the operation and no erase operation will be performed. If the memory is in the protected state, then the Block Erase command will not be executed, and the device will return to the idle state once the CS pin has been deasserted. SCK CS SI SO MSB MSB 23 1 0 00000010 67 5 410 11 9 812 39 37 38 33 36 35 34 31 32 29 30 OPCODE HIGH-IMPEDANCE AAAA AAA A A MSB DDDDDDD D ADDRESS BITS A23-A0 DATA IN SCK CS SI SO MSB MSB 23 1 0 00000010 67 5 49 839 37 38 33 36 35 34 31 32 29 30 OPCODE HIGH-IMPEDANCE AA AAA A MSB DDDDDDD D ADDRESS BITS A23-A0 DATA IN BYTE 1 MSB DDDDDDD D DATA IN BYTE n |
Similar Part No. - AT25F512B-SSH-T |
|
Similar Description - AT25F512B-SSH-T |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |