Electronic Components Datasheet Search |
|
ENA1156 Datasheet(PDF) 4 Page - Sanyo Semicon Device |
|
ENA1156 Datasheet(HTML) 4 Page - Sanyo Semicon Device |
4 / 26 page LC87F7DC8A No.A1156-4/26 Interrupts • 31 sources, 10 vector addresses 1) Provides three levels (low (L), high (H), and highest (X)) of multiplex interrupt control. Any interrupt requests of the level equal to or lower than the current interrupt are not accepted. 2) When interrupt requests to two or more vector addresses occur at the same time, the interrupt of the highest level takes precedence over the other interrupts. For interrupts of the same level, the interrupt into the smallest vector address takes precedence. No. Vector Address Level Interrupt Source 1 00003H X or L INT0 2 0000BH X or L INT1 3 00013H H or L INT2/T0L/INT4/remote control receiver1 4 0001BH H or L INT3/base timer/INT5/remote control receiver2 5 00023H H or L T0H/INT6 6 0002BH H or L T1L/T1H/INT7 7 00033H H or L SIO0/UART1 receive/UART2 receive/T8L/T8H 8 0003BH H or L SIO1/UART1 transmit/UART2 transmit 9 00043H H or L ADC/MIC/T6/T7/PWM4/PWM5 10 0004BH H or L Port 0/T4/T5 • Priority levels X > H > L • Of interrupts of the same level, the one with the smallest vector address takes precedence. • IFLG (List of interrupt source flag function) 1) Shows a list of interrupt source flags that caused a branching to a particular vector address (shown in the diagram above). Subroutine Stack Levels: 2048 levels (The stack is allocated in RAM.) High-speed Multiplication/Division Instructions • 16 bits × 8 bits (5 tCYC execution time) • 24 bits × 16 bits (12 tCYC execution time) • 16 bits ÷ 8 bits (8 tCYC execution time) • 24 bits ÷ 16 bits (12 tCYC execution time) Oscillation Circuits • RC oscillation circuit (internal): For system clock • CF oscillation circuit: For system clock, with internal Rf • Crystal oscillation circuit: For low-speed system clock, with internal Rf • Frequency variable RC oscillation circuit (internal): For system clock 1) Adjustable in ±4% (typ.) step from a selected center frequency. 2) Measures oscillation clock using a input signal from XT1 as a reference. System Clock Divider Function • Can run on low current. • The minimum instruction cycle selectable from 300ns, 600ns, 1.2μs, 2.4μs, 4.8μs, 9.6μs, 19.2μs, 38.4μs, and 76.8 μs (at a main clock rate of 10MHz). Standby Function • HALT mode: Halts instruction execution while allowing the peripheral circuits to continue operation. (Some parts of the serial transfer function stops operation.) 1) Oscillation is not halted automatically. 2) Canceled by a system reset or occurrence of an interrupt Continued on next page. |
Similar Part No. - ENA1156 |
|
Similar Description - ENA1156 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |