HD404052H datasheet(10/103 Pages) RENESAS

Part #	HD404052H

Description	microcomputer designed to increase program productivity

Download	103 Pages

Scroll/Zoom	100%

Manufacturer	RENESAS [Renesas Technology Corp]

Direct Link	http://www.renesas.com

Logo

10 / 103 page

HD404054 Series/HD404094 Series

8

RAM-Mapped Register Area ($000–$03F):

• Interrupt Control Bits Area ($000–$003)

This area is used for interrupt control bits (figure 3). These bits can be accessed only by RAM bit

manipulation instructions (SEM/SEMD, REM/REMD, and TM/TMD). However, note that not all the

instructions can be used for each bit. Limitations on using the instructions are shown in figure 4.

• Special Function Register Area ($004–$018, $024–$034)

This area is used as mode registers and data registers for external interrupts, serial interface 1,

timer/counters, voltage comparator, and as data control registers for I/O ports. The structure is shown in

figures 2 and 5. These registers can be classified into three types: write-only (W), read-only (R), and

read/write (R/W). RAM bit manipulation instructions cannot be used for these registers.

• Register Flag Area ($020–$023)

This area is used for the WDON, and other register flags and interrupt control bits (figure 3). These bits

can be accessed only by RAM bit manipulation instructions (SEM/SEMD, REM/REMD, and

TM/TMD). However, note that not all the instructions can be used for each bit. Limitations on using

the instructions are shown in figure 4.

Memory Register (MR) Area ($040–$04F): Consisting of 16 addresses, this area (MR0–MR15) can be

accessed by register-register instructions (LAMR and XMRA). The structure is shown in figure 6.

Data Area ($090–$23F): 432 digits from $090 to $23F.

Stack Area ($3C0–$3FF): Used for saving the contents of the program counter (PC), status flag (ST), and

carry flag (CA) at subroutine call (CAL or CALL instruction) and for interrupts. This area can be used as a

16-level nesting subroutine stack in which one level requires four digits. The data to be saved and the save

conditions are shown in figure 6.

The program counter is restored by either the RTN or RTNI instruction, but the status and carry flags can

only be restored by the RTNI instruction. Any unused space in this area is used for data storage.

Similar Part No. - HD404052H

Manufacturer	Part #	Datasheet	Description
Hitachi Semiconductor	HD404052H	395Kb / 101P	HMCS400-series microcomputers designed to increase program productivity with large-capacity memory

Manufacturer	Part #	Datasheet	Description
Renesas Technology Corp	HD404318	305Kb / 68P	microcomputer designed to increase program productivity
Renesas Technology Corp	HD404328	311Kb / 96P	microcomputer designed to increase program productivity
Hitachi Semiconductor	HD404054	395Kb / 101P	HMCS400-series microcomputers designed to increase program productivity with large-capacity memory
Renesas Technology Corp	HD404339	321Kb / 80P	microcomputer with large-capacity memory designed to
Rochester Electronics	M80C31BH	601Kb / 9P	CMOS SINGLE - CHIP 8-BIT MICROCOMPUTER 64K program Memory Space
STMicroelectronics	PM0212	161Kb / 22P	How to program the STM8TL5xxx Flash program memory and data EEPROM
Level One	GEP-0520	689Kb / 3P	9K jumbo frames to increase data transfer rates
STMicroelectronics	PM0083	411Kb / 13P	How to program STM8T143 OTP options
	PM0051	198Kb / 27P	How to program STM8S and STM8A Flash program memory and data EEPROM
	PM0054	246Kb / 28P	How to program STM8L and STM8AL Flash program memory and data EEPROM