Electronic Components Datasheet Search |
|
ST755CN Datasheet(PDF) 3 Page - STMicroelectronics |
|
ST755CN Datasheet(HTML) 3 Page - STMicroelectronics |
3 / 9 page ELECTRICAL CHARACTERISTICS (Refer to the test circuits, VCC = 5V, Vout = -5.25 to -4.75V, Iload = 0mA, Ta =Tmin to Tmax unless otherwise specified. Typical Value are referred at Ta =25 oC) Symbol Parameter Test Conditions Min. Typ. Max. Unit VIN Input Voltage 2.7 11 V Vo Output Voltage Io =0 mA to 200 mA VCC = 4.5 to 6.2 V -5.25 -5 -4. 75 V Io Output Current VCC = 4.5 to 6.2 V Ta =0 oCto 70 oC VCC = 4.5 to 6.2 V Ta = -40 oCto 85 oC VCC =4 V Vout =-5 V VCC = 2.7 V Vout =-5 V 200 175 275 175 125 mA mA mA mA ISUPPLY Supply Current (Including Switching Current) No Load, VSHDN =VCC 1. 2 3.5 mA IOFF Standby Current No Load, VSHDN = 0V 10 100 µA ISC Short Circuit Current 1. 2 A ∆Vo Line Regulation VCC = 4 to 6.2 V 0. 1 %/V ∆Vo Load Regulation Io = 0 mA to 200 mA 0.003 %/mA VREF Reference Voltage Ta =25 oC 1.18 1.25 1.32 V ∆VREF Reference Dritft Ta =Tmin to Tmax 50 ppm/ oC RDSON LX On Resistance 0. 7 Ω ILEAK LX Leakage Current VDS =10 V 1 µA ISH Shutdown Pin Current 1 µA Vil Shutdown Input Low Threshold 0.25 V Vih Shutdown Input High Threshold 2V fo Oscillator Frequency 160 KHz ν Power Efficency Io = 100 mA 68 % CC Compensation Pin Impedance 7. 5 K Ω Do not overload or short the Output to Ground. If the above conditions are observerd, the device may be damaged. APPLICATION INFORMATION The ST755 is an IC developed for voltage conversion from an input voltage ranging from +2.4V to 11V to a regulated adjustable negative output limited by |Vout| ≤ 12.7V-VIN. The circuit adopts a current-mode PWM control scheme to achieve good efficiency , high stability and low noise performance. The figure in the first page shown the detailed block diagram of the device. ST755 is realized in a BCD technology in order to achieve high temperature stability, the best REFERENCE precision , a very low quiescent current and jitter free operations. The final stage is built around a 0.7 Ω - 2A P-Channel Power MOS. A fraction of the output current is splitted out for current detection.Internal clock frequency is fixed to 160KHz. Error amplifier drives the PWM comparator in order to keep 0V on the CC input. So R3 and R4 resistors are calculated by the following formulae R4 = (|Vout|/Vref)*R3 (see fig 1). For R3 can be choosen any value between 2K Ω and 20KΩ. Soft-Start (SS) input is a voltage dependent-output current limit (see figure 9, Switch Current Limit vs. SS Input Voltage). SS pin is internally pulled to Vref through a 1.2 M Ω resistor. Applying an appropiate capacitor at SS input is possible to obtain a soft-start current limitation during power up. Forcing Soft-Start (SS) input to a lower voltage through a resistive voltage driver (R1 and R2), the maximum LX curent limit can be lowered according the diagram showed in figure 9. When SHDN input is low, the total current consumption is reduced to 10 µA. ST755 3/9 |
Similar Part No. - ST755CN |
|
Similar Description - ST755CN |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |