CAT.8100T

ALUMINUM ELECTROLYTIC CAPACITORS

0.3 MAX.

C

±0.2

H

H

0.3 MAX.

C

±0.2

L

±0.3

L

±0.5

Series

Capacitance

Lot No.

Lot No.

Capacitance

Plastic platform

Plastic platform

Series

Trade mark

Voltage (C:16V)

Voltage (V:35V)

Negative

Positive

Negative

Positive

Pressure relief vent

U

1

U

2

D

3

1

4

C

5

2

6

2

7

0

8

M

9

C

10

R

11

1

12

G

13

S

14

φ D × L

4 ~ 6.3

CR

NR

Configuration

Package code

Capacitance tolerance (

±20%)

Rated Capacitance (22

µF)

Rated voltage (16V)

Series name

Type

Code

(mm)

A

B

C

E

L

H

4

× 5.8

1.8

4.3

4.3

1.0

5.8

0.5 ~ 0.8

5

× 5.8

2.1

5.3

5.3

1.3

5.8

0.5 ~ 0.8

6.3

× 5.8

2.4

6.6

6.6

2.2

5.8

0.5 ~ 0.8

6.3

× 7.7

2.4

6.6

6.6

2.2

7.7

0.5 ~ 0.8

8

× 10

2.9

8.3

8.3

3.1

10

0.8 ~ 1.1

10

× 10

3.2

10.3

10.3

4.5

10

0.8 ~ 1.1

φ D × L

UD

series

Chip Type, Low Impedance

Designed for surface mounting on high density PC board.

Applicable to automatic mounting machine using carrier tape.

Chip Type

Specifications

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Leakage Current

tan

δ

Stability at Low Temperature

Endurance

Shelf Life

Resistance to soldering

heat

Marking

Performance Characteristics

Item

– 55 ~ +105°C

6.3 ~ 50V

1 ~ 1500µF

± 20% at 120Hz, 20°C

After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA), whichever is greater.

Black print on the case top.

After 5000 hours' (2000 hours for

φD 6.3)

application of rated voltage at 105°C , capacitors

meet the characteristic requirements listed at

right.

After leaving capacitors under no load at 105°C for 1000 hours,

they meet the specified value for endurance characteristics listed above.

Measurement frequency : 120Hz, Temperature : 20°C

Measurement frequency : 120Hz

(

) is

φ8 over

Z– 25°C / Z+20°C

Z– 55°C / Z+20°C

Rated voltage (V)

Impedance ratio

ZT / Z20 (MAX.)

16

2

4

10

2

4

6.3

3

5

25

2

3

35

2

3

50

2

3

Rated voltage (V)

tan

δ (MAX.)

50

0.12 (0.14)

35

0.12 (0.14)

25

0.14 (0.16)

16

0.16 (0.20)

10

0.20 (0.24)

6.3

0.26 (0.28)

Within ±30% of initial value

Initial specified value or less

200% or less of initial specified value

Capacitance change

tan

δ

Leakage current

Capacitance change

Leakage current

tan

δ

Within ±10% of initial value

Initial specified value or less

Initial specified value or less

The capacitors shall be kept on the hot plate maintained at 250°C

for 30 seconds. After removing from the hot plate and restored

at room temperature, they meet the characteristic requirements

listed at right.

UD

(

φ4 ~ 6.3)

(

φ8, φ10×10L)

Dimension table in next page.

Voltage

V

6.3

10

16

25

35

50

Code

j

ACE

V

H

WG

Low Impedance

Low Impedance

UU

In this case,

will be put at 11th digit of type numbering system.

L