Electronic Components Datasheet Search |
|
M29F040-150N5R Datasheet(PDF) 6 Page - STMicroelectronics |
|
M29F040-150N5R Datasheet(HTML) 6 Page - STMicroelectronics |
6 / 31 page Memory Blocks The memory blocks of the M29F040 are shown in Figure 3. The memory array is divided in 8 uniform blocks of 64 Kbytes. Each block can be erased separately or any combination of blocks can be erased simultaneously. The Block Erase operation is managed automatically by the P/E.C. The opera- tion can be suspended in order to read from any other block, and then resumed. Block Protection provides additional data security. Each uniform block can be separately protected or unprotected against Program or Erase. Bringing A9 and G to VID initiates protection, while bringing A9, G and E to VID cancels the protection. The block affected during protection is addressed by the in- puts on A16, A17, and A18. Unprotect operation affects all blocks. Operations Operations are defined as specific bus cycles and signals which allow Memory Read, Command Write, Output Disable, Standby, Read Status Bits, Block Protect/Unprotect, Block Protection Check and Electronic Signature Read. They are shown in Tables 3, 4, 5. Read. Read operations are used to output the contents of the Memory Array, the Status Register or the Electronic Signature. Both Chip Enable E and Output Enable G must be low in order to read the output of the memory. The Chip Enable input also provides power control and should be used for device selection. Output Enable should be used to gate data onto the output independent of the device selection. The data read depends on the previous command written to the memory (see instructions RST and RSIG, and Status Bits). Write. Write operations are used to give Instruction Commands to the memory or to latch input data to be programmed. A write operation is initiated when Chip Enable E is Low and Write Enable W is Low with Output Enable G High. Addresses are latched on the falling edge of W or E whichever occurs last. Commands and Input Data are latched on the rising edge of W or E whichever occurs first. Output Disable. The data outputs are high imped- ance when the Output Enable G is High with Write Enable W High. Standby. The memory is in standby when Chip Enable E is High and Program/Erase Controller P/E.C. is Idle. The power consumption is reduced to the standby level and the outputs are high im- pedance, independent of the Output Enable G or Write Enable W inputs. Automatic Standby. After 150ns of inactivity and when CMOS levels are driving the addresses, the chip automatically enters a pseudo standby mode where consumption is reduced to the CMOS standby value, while outputs are still driving the bus. Electronic Signature. Two codes identifying the manufacturer and the device can be read from the memory, the manufacturer’s code for STMicroelec- tronics is 20h, and the device code is E2h for the M29F040. These codes allow programming equip- ment or applications to automatically match their interface to the characteristics of the particular manufacturer’s product. The Electronic Signature is output by a Read operation when the voltage applied to A9 is at VID and address inputs A1 and A6 are at Low. The manufacturer code is output when the Address input A0 is Low and the device code when this input is High. Other Address inputs are ignored. The codes are output on DQ0-DQ7. This is shown in Table 4. The Electronic Signature can also be read, without raising A9 to VID by giving the memory the instruc- tion RSIG (see below). Block Protection. Each uniform block can be separately protected against Program or Erase. Block Protection provides additional data security, as it disables all program or erase operations. This mode is activated when both A9 and G are set to VID and the block address is applied on A16-A18. Block Protection is programmed using a Presto F program like algorithm. Protection is initiated on the edge of W falling to VIL. Then after a delay of 100 µs, the edge of W rising to VIH ends the protection operation. Protection verify is achieved by bringing G, E and A6 to VIL while W is at VIH and A9 at VID. Under these conditions, reading the data output will yield 01h if the block defined by the inputs on A16-A18 is protected. Any attempt to program or erase a protected block will be ignored by the device. Any protected block can be unprotected to allow updating of bit contents. All blocks must be pro- tected before an unprotect operation. Block Un- protect is activated when A9, G and E are at VID. The addresses inputs A6, A12, A16 must be main- tained at VIH. Block Unprotect is performed through a Presto F Erase like algorithm. Unprotect is initi- ated by the edge of W falling to VIL. After a delay of 10ms, the edge of W rising to VIH will end the unprotection operation. Unprotect verify is achieved by bringing G and E to VIL while A6 and W are at VIH and A9 at VID. In these conditions, reading the output data will yield 00h if the block defined by the inputs on A16-A18 has been suc- cessfully unprotected. All combinations of A16- A18 must be addressed in order to ensure that all of the 8 uniform blocks have been unprotected. Block Protection Status is shown in Table 5. 6/31 M29F040 |
Similar Part No. - M29F040-150N5R |
|
Similar Description - M29F040-150N5R |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |