Electronic Components Datasheet Search |
|
M295V002NT-90P6TR Datasheet(PDF) 11 Page - STMicroelectronics |
|
M295V002NT-90P6TR Datasheet(HTML) 11 Page - STMicroelectronics |
11 / 29 page AI01275B 3V High Speed 0V 1.5V 2.4V Standard 0.45V 2.0V 0.8V Figure 4. AC Testing Input Output Waveform AI01276B 1.3V OUT CL CL = 30pF for High Speed CL = 100pF for Standard CL includes JIG capacitance 3.3k Ω 1N914 DEVICE UNDER TEST Figure 5. AC Testing Load Circuit Symbol Parameter Test Condition Min Max Unit CIN Input Capacitance VIN =0V 6 pF COUT Output Capacitance VOUT =0V 12 pF Note: 1. Sampled only, not 100% tested. Table 12. Capacitance(1) (TA =25 °C, f = 1 MHz ) Auto Select (AS) Instruction. This instruction uses the two Coded cycles followed by one write cycle giving the command 90h to address 555h for command set-up. Asubsequentread will output the manufacturer code and the device code or the block protection status depending on the levels of A0 and A1. The manufacturer code, 20h, is output when the addresses lines A0 and A1 are Low, the device code is output when A0 is High with A1 Low. The AS instruction also allows access to the block protectionstatus. After giving the AS instruction, A0 is set to VIL with A1 at VIH, while A13-A17 define the address of the block to be verified. A read in these conditions will output a 01h if the block is protected and a 00h if the block is not protected. Program (PG) Instruction. This instruction uses four write cycles. The Program command A0h is written to address 555h on the third cycle after two Coded cycles. A fourth write operation latches the Address on the falling edge of W or E and the Data to be written on the rising edge and starts the P/E.C. Read operations output the Status Register bits after the programming has started. Memory programming is made only by writing ’0’ in place of ’1’. Status bits DQ6 and DQ7 determine if program- ming is on-goingand DQ5 allows verification of any possible error. Programming at an address not in blocks being erased is also possible during erase suspend. In this case, DQ2 will toggle at the ad- dress being programmed. High Speed Standard Input Rise and Fall Times ≤ 10ns ≤ 10ns Input Pulse Voltages 0 to 3V 0.45V to 2.4V Input and Output Timing Ref. Voltages 1.5V 0.8V and 2V Table 11. AC Measurement Conditions 11/29 M29F002T, M29F002NT, M29F002B |
Similar Part No. - M295V002NT-90P6TR |
|
Similar Description - M295V002NT-90P6TR |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |